{"title":"Windlass Parts, Switches \u0026 Solenoids","description":null,"products":[{"product_id":"sea-dog-foot-switch-for-windlasses-12v-30a-304-stainless-steel-with-rubber-cover-420430-1","title":"Sea-Dog Foot Switch 420430-1, Stainless Steel Momentary Deck Switch for Windlasses","description":"\u003cp\u003eThe Sea-Dog Foot Switch, part number 420430-1, is a momentary-contact deck switch designed for hands-free operation of windlasses and other marine equipment. The switch is normally off and turns on only while depressed by foot, then returns to the off position when released, making it ideal for windlass control where continuous foot pressure should be required for safe operation.\u003c\/p\u003e\u003cp\u003eConstruction is stamped 304 stainless steel with a rubber cover, giving the switch strong corrosion resistance for exposed deck installations. A rubber seal combined with the stainless bezel keeps water out of the switch body, protecting the internal contacts from spray and rain. The switch is rated 12 volts at 30 amps, suitable for direct windlass circuit control.\u003c\/p\u003e\u003cp\u003eInstallation requires a 2 inch diameter hole to accept the switch body, with an overall footprint of 4-7\/16 inches by 3-5\/16 inches. The switch bracket can be mounted on the surface of the deck or mortised flush for a lower-profile installation. It installs using ten #8 RH fasteners, which are not included. A replacement rubber seal is available separately for this switch.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Sea-Dog\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e 420430-1\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Stamped 304 stainless steel with rubber cover\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSwitch Action:\u003c\/strong\u003e Normally off, momentarily on when depressed by foot\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting Hole Size:\u003c\/strong\u003e 2 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOverall Dimensions (A x B x C):\u003c\/strong\u003e 4-7\/16 inches x 3-5\/16 inches x 2 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVoltage:\u003c\/strong\u003e 12 volts\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAmperage:\u003c\/strong\u003e 30 amps\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFastener Type:\u003c\/strong\u003e #8 RH (not included, 10 required)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting Style:\u003c\/strong\u003e Surface mount or flush mortise mount\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 0.752 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 035514420341\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eUniversal foot switch for windlasses and other 12 volt marine deck equipment requiring a momentary-contact foot control.\u003c\/p\u003e\n\u003ch3\u003eReplaces (OEM)\u003c\/h3\u003e\n\u003cp\u003eNo OEM cross-reference numbers apply to this part.\u003c\/p\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat is the Sea-Dog 420430-1 foot switch used for?\u003c\/strong\u003e This foot switch is designed to control windlasses and other 12 volt marine deck equipment, providing momentary on operation while the pedal is depressed by foot.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow does the momentary action work?\u003c\/strong\u003e The 420430-1 foot switch is normally off and only closes the circuit while it is being pressed; releasing the pedal returns it to the off position, which is a common safety feature for windlass controls.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat size hole do I need to install this switch?\u003c\/strong\u003e A 2 inch diameter hole is required to mount the Sea-Dog 420430-1 foot switch.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat are the overall dimensions of the switch?\u003c\/strong\u003e The 420430-1 measures 4-7\/16 inches by 3-5\/16 inches, with a 2 inch mounting hole depth dimension, per Sea-Dog specifications.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat voltage and amperage is this switch rated for?\u003c\/strong\u003e 12 volts at 30 amps is the rating for the Sea-Dog 420430-1 foot switch.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan this foot switch be mounted flush with the deck?\u003c\/strong\u003e Yes, the switch bracket for the 420430-1 can either be mounted on the surface of the deck or mortised in for a flush installation.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the switch made of?\u003c\/strong\u003e Corrosion resistant stamped 304 stainless steel with a rubber cover is used to construct the Sea-Dog 420430-1 foot switch, making it suited to exposed marine deck environments.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow is the switch protected from water?\u003c\/strong\u003e A rubber seal paired with the stainless steel bezel on the 420430-1 keeps water out of the switch housing.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAre mounting fasteners included with the switch?\u003c\/strong\u003e No, the Sea-Dog 420430-1 installs with ten #8 RH fasteners that are not included and must be sourced separately.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much does the foot switch weigh?\u003c\/strong\u003e The Sea-Dog 420430-1 foot switch weighs 0.752 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs a replacement seal available for this switch?\u003c\/strong\u003e Yes, Sea-Dog offers a separate replacement seal for the 420430-1 foot switch.\u003c\/p\u003e","brand":"Sea-Dog","offers":[{"title":"Default Title","offer_id":48988774957275,"sku":"S-D-420430-1","price":41.38,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/5005.jpg?v=1784429329"},{"product_id":"lewmar-12v-dual-direction-windlass-solenoid-contactor-replaces-68000939-fits-sprint-horizon-pro-series-pro-fish-windlasses","title":"Lewmar Dual Direction Windlass Solenoid 0052507 for Sprint, Horizon and Pro Series Windlasses (Replaces 68000939)","description":"\u003cp\u003eThe Lewmar Dual Direction Windlass Solenoid, part number 0052507, is a 12V contactor that controls the up\/down (let-out and heave-up) direction of a Lewmar windlass. It is built as a direct replacement for the earlier Lewmar solenoid, part 68000939, so it drops into the same control circuit without modification. The unit is finished in black and constructed to withstand the vibration, moisture, and load-switching demands of routine anchor and windlass operation aboard a boat.\u003c\/p\u003e\u003cp\u003eThis solenoid is designed for use with Lewmar Sprint 600, Sprint 1000, Sprint 1500, and Sprint 3000A windlasses, as well as the Horizon 400, Horizon 600, Horizon 600F, Horizon 900, and Horizon 900F models, along with Lewmar Pro Series and Pro Fish windlasses. Because these windlasses operate in both directions, the unit functions as a dual-direction contactor rather than a single-direction relay, and it should be installed as part of a dual-direction solenoid setup. It ships as a single solenoid unit, weighs 2.22 pounds, and is backed by a 1-year manufacturer warranty.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Lewmar\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e 0052507\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e Dual Direction Windlass Solenoid (Contactor)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVoltage:\u003c\/strong\u003e 12V\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e Black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct Dimensions:\u003c\/strong\u003e 6 x 6 x 6 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 2.22 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIncluded Components:\u003c\/strong\u003e Solenoid\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWarranty:\u003c\/strong\u003e 1 Year Manufacturer\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOEM Cross Reference:\u003c\/strong\u003e 68000939\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 000000052507\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatible Windlass Models:\u003c\/strong\u003e Sprint 600, Sprint 1000, Sprint 1500, Sprint 3000A, Horizon 400, Horizon 600, Horizon 600F, Horizon 900, Horizon 900F, Pro Series, Pro Fish\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eLewmar Sprint 600, Sprint 1000, Sprint 1500, and Sprint 3000A windlasses\u003c\/li\u003e\n\u003cli\u003eLewmar Horizon 400, Horizon 600, Horizon 600F, Horizon 900, and Horizon 900F windlasses\u003c\/li\u003e\n\u003cli\u003eLewmar Pro Series and Pro Fish windlasses\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eReplaces (OEM)\u003c\/h3\u003e\u003cul\u003e\u003cli\u003e68000939\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat is Lewmar part 0052507?\u003c\/strong\u003e Part 0052507 is a Lewmar 12V dual direction solenoid, also called a contactor, that switches power to a windlass motor in both the up and down directions.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhich windlasses does the 0052507 solenoid fit?\u003c\/strong\u003e It is designed for Lewmar Sprint 600, Sprint 1000, Sprint 1500, and Sprint 3000A windlasses, as well as Horizon 400, Horizon 600, Horizon 600F, Horizon 900, and Horizon 900F windlasses, plus Pro Series and Pro Fish windlasses.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes 0052507 replace an older Lewmar part number?\u003c\/strong\u003e Yes, this solenoid is a direct replacement for Lewmar part 68000939 and can be installed in place of that earlier part.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs this a single-direction or dual-direction solenoid?\u003c\/strong\u003e The 0052507 is a dual direction solenoid, meaning it controls both the let-out and heave-up functions of the windlass rather than just one direction.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much does the Lewmar 0052507 solenoid weigh?\u003c\/strong\u003e The solenoid weighs 2.22 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat are the dimensions of the solenoid unit?\u003c\/strong\u003e The Lewmar 0052507 solenoid measures 6 x 6 x 6 inches.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat voltage is this solenoid rated for?\u003c\/strong\u003e It is a 12V unit, matching the 12-volt electrical systems used on most Lewmar Sprint, Horizon, and Pro Series windlasses.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat color is the 0052507 solenoid?\u003c\/strong\u003e It is finished in black.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is included when I order this part?\u003c\/strong\u003e Ordering part 0052507 includes one solenoid unit; it is used as part of a dual direction solenoid setup for the windlass control circuit.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs a warranty included with the Lewmar 0052507 solenoid?\u003c\/strong\u003e Yes, it carries a 1-year manufacturer warranty.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan I use this solenoid on a single-direction windlass control?\u003c\/strong\u003e No, the 0052507 is built for dual direction operation and should be installed as part of a dual-direction solenoid arrangement, not a single-direction circuit.\u003c\/p\u003e","brand":"Lewmar","offers":[{"title":"Default Title","offer_id":48991709987035,"sku":"LEW-52507","price":242.14,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/1__95533.1763741606.500.750.jpg?v=1785188032"},{"product_id":"lewmar-dual-direction-toggle-switch-0052519-for-small-windlasses","title":"Lewmar Dual Direction Toggle Switch 0052519 for Small Windlasses","description":"\u003cp\u003eThe Lewmar Dual Direction Toggle Switch, part number 0052519, is a panel-mount control switch built for smaller anchor windlasses. It has a contactor built directly into the switch body, so it can drive the windlass motor circuit without needing a separate remote solenoid for basic up\/down operation. The switch is a two-position, dual direction (up-down) toggle with an ON-OFF control type and normally open contact configuration wired in series, matching the standard control layout used on compact windlass installations.\u003c\/p\u003e\u003cp\u003eConstruction is metal, with copper alloy contacts for reliable current-carrying capacity and insulation resistance rated at 100 megaohms, supporting long-term durability in a marine electrical environment. Termination is push-on quick-connect, simplifying wiring at installation or when replacing an existing switch. The switch mounts through a panel cutout for a clean helm or deck-box installation, and it is designed specifically for use with windlass systems.\u003c\/p\u003e\u003cp\u003eThis is a genuine Lewmar part sold as a single switch unit, intended as a direct replacement or upgrade for the toggle switch on compatible smaller Lewmar windlass installations.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Lewmar\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e 0052519\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting Type:\u003c\/strong\u003e Panel Mount\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Metal\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTerminal:\u003c\/strong\u003e Push On\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eContact Material:\u003c\/strong\u003e Copper Alloy\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInsulation Resistance:\u003c\/strong\u003e 100 Megaohms\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOperation Mode:\u003c\/strong\u003e ON OFF\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eContact Type:\u003c\/strong\u003e Normally Open\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCircuit Type:\u003c\/strong\u003e Series\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatible Devices:\u003c\/strong\u003e Windlasses\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatible with Vehicle Type:\u003c\/strong\u003e Marine\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnectivity Protocol:\u003c\/strong\u003e Wired\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector Type:\u003c\/strong\u003e Quick Connect\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eControl Type:\u003c\/strong\u003e ON-OFF\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNumber of Positions:\u003c\/strong\u003e 2\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSwitch Type:\u003c\/strong\u003e Toggle\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUnit Count:\u003c\/strong\u003e 1\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 0.21 pounds\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat does the Lewmar 0052519 toggle switch control?\u003c\/strong\u003e It is a dual direction toggle switch for smaller windlasses, letting the operator run the windlass motor up or down from a single panel-mounted switch.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes this switch include a built-in contactor?\u003c\/strong\u003e Yes, the Lewmar 0052519 has a contactor built into the switch itself, so it can switch the windlass motor circuit directly.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs this switch meant for large or small windlasses?\u003c\/strong\u003e The Lewmar 0052519 is designed for smaller windlasses, not the larger models that typically require a separate remote solenoid setup.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow is the Lewmar 0052519 switch mounted?\u003c\/strong\u003e It is a panel mount switch, installed through a cutout in a helm panel or deck box rather than surface mounted.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the switch made of?\u003c\/strong\u003e The Lewmar 0052519 toggle switch has a metal body with copper alloy contacts for reliable current handling.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat type of electrical contact does this switch use?\u003c\/strong\u003e It uses a normally open contact type wired in a series circuit, with a two-position ON-OFF control layout.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow do the wires connect to this switch?\u003c\/strong\u003e Termination is push-on quick-connect, so wiring is done with quick-connect terminals rather than screw terminals.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much does the Lewmar 0052519 switch weigh?\u003c\/strong\u003e The switch weighs 0.21 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the Lewmar 0052519 a genuine Lewmar part?\u003c\/strong\u003e Yes, part number 0052519 is a genuine Lewmar dual direction toggle switch, not a generic aftermarket equivalent.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the insulation resistance rating of this switch?\u003c\/strong\u003e The Lewmar 0052519 is rated at 100 megaohms insulation resistance.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow many positions does the toggle have?\u003c\/strong\u003e It is a two-position toggle switch with ON-OFF control for dual direction operation.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is included when ordering this part?\u003c\/strong\u003e Ordering part number 0052519 includes one Lewmar dual direction toggle switch unit.\u003c\/p\u003e","brand":"Lewmar","offers":[{"title":"Default Title","offer_id":49025131708635,"sku":"LEW-0052519","price":121.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/Untitled-1__96258.1763741551.500.750.jpg?v=1785329119"},{"product_id":"lewmar-dual-direction-solenoid-0052531-12v-reversing-contactor-for-sprint-600-1000-horizon-400-600-600f-900-900f-pro-series-windlasses","title":"Lewmar Dual Direction Solenoid 0052531, 12V Reversing Contactor for Sprint 600\/1000, Horizon 400\/600\/600F\/900\/900F \u0026 Pro Series Windlasses","description":"\u003cp\u003eThe Lewmar Dual Direction Solenoid 0052531 is a 12 volt DC reversing contactor built for Lewmar electric windlasses that use permanent magnet motors. It is a changeover-type contactor, meaning a single unit switches the motor's polarity to drive the windlass in both directions, letting the anchor rode pay out and haul in from the same switch or helm control. This part is the direct replacement for the contactor inside the windlass control circuit, restoring proper up-and-down function when a worn or failing solenoid causes sluggish response, one-direction-only operation, or intermittent anchoring control.\u003c\/p\u003e\u003cp\u003eElectrically, it is rated for a 12 volt DC coil and carries a 100 watt rating, with a minimum switching voltage of 12 volts DC, matching the demands of continuous-duty windlass motors. It ships as a single solenoid unit ready to wire into the existing control circuit, making it a straightforward service item for routine maintenance or troubleshooting an anchoring system that has stopped responding correctly. It fits Lewmar Sprint 600 and Sprint 1000, Horizon 400, 600, 600F, 900 and 900F, Pro Series, and Pro Fish windlasses, so it is a common replacement across several models in the Lewmar electric windlass lineup.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Lewmar\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e 0052531\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eContact Type:\u003c\/strong\u003e Changeover\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCoil Voltage:\u003c\/strong\u003e 12 Volts DC\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMinimum Switching Voltage:\u003c\/strong\u003e 12 Volts DC\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWattage:\u003c\/strong\u003e 100 watts\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eItem Type:\u003c\/strong\u003e 12V Windlass Solenoid, Dual Direction\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIncluded Components:\u003c\/strong\u003e Solenoid\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 2.13125 pounds\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eLewmar Sprint 600\u003c\/li\u003e\n\u003cli\u003eLewmar Sprint 1000\u003c\/li\u003e\n\u003cli\u003eLewmar Horizon 400\u003c\/li\u003e\n\u003cli\u003eLewmar Horizon 600\u003c\/li\u003e\n\u003cli\u003eLewmar Horizon 600F\u003c\/li\u003e\n\u003cli\u003eLewmar Horizon 900\u003c\/li\u003e\n\u003cli\u003eLewmar Horizon 900F\u003c\/li\u003e\n\u003cli\u003eLewmar Pro Series windlasses\u003c\/li\u003e\n\u003cli\u003eLewmar Pro Fish windlasses\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat does the Lewmar 0052531 solenoid do?\u003c\/strong\u003e The Lewmar 0052531 is a changeover-type 12 volt DC contactor that reverses polarity to a permanent magnet windlass motor, letting a single control switch drive the windlass both up and down.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhich Lewmar windlasses use part 0052531?\u003c\/strong\u003e Part 0052531 fits Lewmar Sprint 600 and Sprint 1000, Horizon 400, 600, 600F, 900 and 900F, Pro Series, and Pro Fish windlasses.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat voltage is the 0052531 solenoid rated for?\u003c\/strong\u003e It is a 12 volt DC coil contactor with a minimum switching voltage of 12 volts DC and a 100 watt rating.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much does the 0052531 solenoid weigh?\u003c\/strong\u003e The Lewmar Dual Direction Solenoid 0052531 weighs 2.13125 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is included when I order part 0052531?\u003c\/strong\u003e The order includes one Lewmar 0052531 solenoid unit, ready to wire into the existing windlass control circuit.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs this a genuine Lewmar part or an aftermarket equivalent?\u003c\/strong\u003e 0052531 is a genuine Lewmar solenoid, manufactured by Lewmar as the direct replacement contactor for its electric windlasses.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat symptoms indicate the windlass solenoid needs replacing?\u003c\/strong\u003e Sluggish response, one-direction-only operation, or a windlass that no longer responds to up or down commands point to a worn or failing contactor like the one replaced by Lewmar 0052531.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes the 0052531 solenoid support both directions of windlass operation?\u003c\/strong\u003e Yes, it is a dual direction, changeover-type contactor, so the same unit switches the motor to run the windlass in reverse as well as forward.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWill this solenoid work with a permanent magnet windlass motor?\u003c\/strong\u003e Yes, the Lewmar 0052531 is designed for dual directional control of permanent magnet motors used in Lewmar electric windlasses.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the Lewmar 0052531 solenoid a changeover contact type?\u003c\/strong\u003e Yes, the contact type is changeover, which is what allows one contactor to control both the up and down direction of the windlass motor.\u003c\/p\u003e","brand":"Lewmar","offers":[{"title":"Default Title","offer_id":49025133248731,"sku":"LEW-52531","price":209.23,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/1__79708.1763741606.500.750.jpg?v=1785329119"},{"product_id":"lewmar-motor-kit-66000610-for-v700-and-sprint-600-windlasses","title":"Lewmar Motor Kit 66000610 for V700 and Sprint 600 Windlasses","description":"\u003cp\u003eThe Lewmar Motor Kit 66000610 is a complete replacement motor for Lewmar V700 and Sprint 600 vertical windlasses. Built from metal for durability in the marine environment, this motor kit delivers fast line speeds while retaining the emergency manual deployment option that lets you lower the anchor by hand if power is unavailable. It is designed as a drop-in replacement motor for windlasses that use 6mm DIN766 chain, 1\/4 inch G4 or BBB chain, or 7mm DIN766 chain, making it a straightforward service part for boat owners maintaining an existing V700 or Sprint 600 installation. Each kit includes one motor, packaged as a single unit for replacement of the original motor on the windlass.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Lewmar\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e 66000610\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct Type:\u003c\/strong\u003e Windlass Motor Kit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatible Windlasses:\u003c\/strong\u003e Lewmar V700, Lewmar Sprint 600\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatible Chain Sizes:\u003c\/strong\u003e 6mm DIN766, 1\/4 inch G4 or BBB, 7mm DIN766\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Metal\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 5.3 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 743683327094\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNumber of Items:\u003c\/strong\u003e 1\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFeature:\u003c\/strong\u003e Emergency manual deployment option\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eLewmar V700 windlass\u003c\/li\u003e\n\u003cli\u003eLewmar Sprint 600 windlass\u003c\/li\u003e\n\u003cli\u003eCompatible with calibrated chains: 6mm DIN766, 1\/4 inch G4 or BBB, 7mm DIN766\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat windlasses does the Lewmar Motor Kit 66000610 fit?\u003c\/strong\u003e The Lewmar Motor Kit 66000610 is a replacement motor for Lewmar V700 and Sprint 600 windlasses.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat chain sizes work with this motor kit?\u003c\/strong\u003e Motor Kit 66000610 is compatible with 6mm DIN766, 1\/4 inch G4 or BBB, and 7mm DIN766 calibrated chains.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much does the Lewmar Motor Kit 66000610 weigh?\u003c\/strong\u003e This motor kit weighs 5.3 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the motor kit made of?\u003c\/strong\u003e The Lewmar Motor Kit 66000610 is constructed of metal for durability aboard a boat.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow many motors are included in this kit?\u003c\/strong\u003e The kit includes one replacement motor, sold as a single unit for the V700 or Sprint 600 windlass.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan I still lower the anchor manually if the motor fails?\u003c\/strong\u003e Yes, the Lewmar Motor Kit 66000610 retains an emergency manual deployment option for lowering the anchor without power.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs this a genuine Lewmar part or an aftermarket copy?\u003c\/strong\u003e Motor Kit 66000610 is a genuine Lewmar replacement part, not an aftermarket equivalent.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes this motor kit fit other Lewmar windlass models besides V700 and Sprint 600?\u003c\/strong\u003e Compatibility for Motor Kit 66000610 is specified for the Lewmar V700 and Sprint 600 windlasses.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs installation of the Lewmar Motor Kit 66000610 straightforward?\u003c\/strong\u003e The kit is designed as a direct replacement motor for the V700 and Sprint 600 windlass, replacing the original motor as a single component.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the UPC for this Lewmar motor kit?\u003c\/strong\u003e The UPC for the Lewmar Motor Kit 66000610 is 743683327094.\u003c\/p\u003e","brand":"Lewmar","offers":[{"title":"Default Title","offer_id":49025133773019,"sku":"LEW-66000610","price":170.13,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/Untitled-1__12333.1763741639.500.750.jpg?v=1785329121"},{"product_id":"lewmar-v3-gypsy-and-drum-windlass-kit-6672221110-139-fastfit-10mm-din-766-3-8-inch-s4-5-16-inch-g40-chain-12v-1000w","title":"Lewmar V3 Gypsy and Drum Windlass Kit 6672221110-139, FastFit, 10mm DIN 766 \/ 3\/8 inch S4 \/ 5\/16 inch G40 Chain, 12V 1000W","description":"\u003cp\u003eThe Lewmar 6672221110-139 is a V3 vertical windlass gypsy and drum kit built around Lewmar's FastFit motor gearbox system. The FastFit design lets one person install the deck unit and motor gearbox with a clamping system that self-aligns the two halves for a correct fit on the first attempt, concealing the drive train, worm gearbox, and splined shaft beneath the deck-mounted gypsy and drum. This kit is sized for the 10mm DIN 766 chain, Campbell 3\/8 inch S4 chain, and 5\/16 inch G40 chain, so it is the correct choice for boats running one of those specific chain types rather than the other chain sizes Lewmar offers in the V3 line.\u003c\/p\u003e\u003cp\u003eThe gypsy and drum are built in stainless steel for corrosion resistance in a marine environment. The complete kit runs on a 12V electrical system with a 1000 watt motor, delivering a maximum pull of 2,260 lbs, and includes the windlass, gypsy, drum, rocker switch, breaker, two-direction solenoid, and handle needed to get the system running. Lewmar recommends this class of windlass for power and sailboats in the 40 foot to 50 foot range. Because the gypsy is matched to a specific chain type and diameter, confirm your chain against the compatibility list below before ordering, since Lewmar sells separate gypsy\/drum kits (different part numbers) for 8mm DIN 766 \/ 8mm ISO 4565 chain and for 10mm ISO \/ Campbell 3\/8 inch S3 \/ Lewmar 9.5mm G40 chain.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Lewmar\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e 6672221110-139\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWindlass Model Line:\u003c\/strong\u003e V3\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGearbox Feature:\u003c\/strong\u003e FastFit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eChain Compatibility:\u003c\/strong\u003e 10mm DIN 766, Campbell 3\/8 inch S4, 5\/16 inch G40\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVoltage:\u003c\/strong\u003e 12V\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMotor Power:\u003c\/strong\u003e 1000 watt\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaximum Pull:\u003c\/strong\u003e 2,260 lbs\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Stainless steel\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIncluded Components:\u003c\/strong\u003e Windlass, gypsy, drum, rocker switch, breaker, two-direction solenoid, handle\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eItem Weight:\u003c\/strong\u003e 53 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eItem Dimensions:\u003c\/strong\u003e 10 x 6 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePackage Dimensions:\u003c\/strong\u003e 24.5 x 18.3 x 11.5 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 743683328329\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRecommended Boat Length:\u003c\/strong\u003e 40 feet to 50 feet\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePower and sailboats 40 feet to 50 feet\u003c\/li\u003e\n\u003cli\u003e10mm DIN 766 chain\u003c\/li\u003e\n\u003cli\u003eCampbell 3\/8 inch S4 chain\u003c\/li\u003e\n\u003cli\u003e5\/16 inch G40 chain\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eReplaces (OEM)\u003c\/h3\u003e\u003cul\u003e\u003cli\u003eNo cross-reference numbers are listed for this part number.\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat chain does the Lewmar 6672221110-139 gypsy kit fit?\u003c\/strong\u003e This kit is built for 10mm DIN 766 chain, Campbell 3\/8 inch S4 chain, or 5\/16 inch G40 chain. Lewmar sells separate gypsy\/drum kits with different part numbers for other chain sizes, so confirm your chain type and diameter before ordering.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs this the same kit as Lewmar's 003 gypsy kit for Campbell S3 chain?\u003c\/strong\u003e No. Part number 6672221110-139 is fitted for 10mm DIN 766, Campbell 3\/8 inch S4, and 5\/16 inch G40 chain. The Campbell 3\/8 inch S3 \/ 10mm ISO \/ Lewmar 9.5mm G40 version is a different Lewmar part number, so the two are not interchangeable.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat voltage and motor power does this windlass kit run on?\u003c\/strong\u003e The 6672221110-139 kit runs on a 12V electrical system with a 1000 watt motor.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much pulling force does this Lewmar windlass provide?\u003c\/strong\u003e Maximum pull is rated at 2,260 lbs for the Lewmar 6672221110-139 V3 gypsy and drum kit.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is included in the box with this windlass kit?\u003c\/strong\u003e The kit includes the windlass, gypsy, drum, rocker switch, breaker, two-direction solenoid, and handle needed to install and power the unit.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat material is the gypsy and drum made from?\u003c\/strong\u003e The gypsy and drum in the Lewmar 6672221110-139 kit are made from stainless steel for corrosion resistance in marine use.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is FastFit and why does it matter for installation?\u003c\/strong\u003e FastFit is Lewmar's motor gearbox mounting system used on this V3 windlass kit. Its clamping design self-aligns the deck unit and motor gearbox, so one person can install the windlass and get a correct fit without repeated adjustment.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much does this windlass kit weigh?\u003c\/strong\u003e The Lewmar 6672221110-139 kit weighs 53 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat size boat is this windlass designed for?\u003c\/strong\u003e This V3 windlass kit is sized for power and sailboats in the 40 foot to 50 foot range.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat are the dimensions of the windlass unit and its shipping package?\u003c\/strong\u003e The windlass item measures 10 x 6 inches, and it ships in a package measuring 24.5 x 18.3 x 11.5 inches.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes this kit come with electrical controls, or just the windlass hardware?\u003c\/strong\u003e It comes with electrical controls: the rocker switch, breaker, and two-direction solenoid are included along with the windlass, gypsy, drum, and handle.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs 6672221110-139 a genuine Lewmar part number?\u003c\/strong\u003e Yes, 6672221110-139 is Lewmar's own manufacturer part number for this V3 gypsy and drum kit, not a generic aftermarket equivalent.\u003c\/p\u003e","brand":"Lewmar","offers":[{"title":"Default Title","offer_id":49025137869019,"sku":"LEW-6672221110-139","price":3938.81,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/img.png?v=1785332781"},{"product_id":"lewmar-circuit-breaker-50a-for-pro-sport-pro-fish-700w-cpx2-v2-24v-c3-24v-vx1-300-vx2-rx2-24v-hx1-500-windlasses","title":"Lewmar Circuit Breaker 50A for Pro-Sport\/Pro-Fish 700W, CPX2\/V2 24V, C3 24V, VX1 300, VX2\/RX2 24V, HX1 500 Windlasses","description":"\u003cp\u003eThe Lewmar Circuit Breaker 50A, part number 68000348, is a 50 amp circuit breaker built to protect Lewmar windlass electrical systems from overcurrent and short-circuit conditions. It serves as the primary safety disconnect between the boat's battery bank and the windlass motor, tripping automatically if current draw exceeds its 50 amp rating to prevent wiring damage or motor burnout. Installed in the power supply line to the windlass, it also functions as a manual on\/off switch for isolating the windlass circuit during maintenance or storage.\u003c\/p\u003e\u003cp\u003eThis 50A breaker is sized specifically for a defined set of Lewmar windlass models: Pro-Sport\/Pro-Fish 700W, CPX2\/V2 24V, C3 24V, VX1 300, VX2\/RX2 24V, and HX1 500. Matching the breaker's amperage to the correct windlass model is essential, since an undersized breaker will trip under normal load and an oversized breaker will not adequately protect the motor and wiring.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Lewmar\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e 68000348\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e Circuit Breaker\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAmperage Rating:\u003c\/strong\u003e 50 Amp\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 0.3 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatible Windlass Models:\u003c\/strong\u003e Pro-Sport\/Pro-Fish 700W, CPX2\/V2 24V, C3 24V, VX1 300, VX2\/RX2 24V, HX1 500\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003ePro-Sport\/Pro-Fish 700W\u003c\/li\u003e\n\u003cli\u003eCPX2\/V2 24V\u003c\/li\u003e\n\u003cli\u003eC3 24V\u003c\/li\u003e\n\u003cli\u003eVX1 300\u003c\/li\u003e\n\u003cli\u003eVX2\/RX2 24V\u003c\/li\u003e\n\u003cli\u003eHX1 500\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat amperage is the Lewmar 68000348 circuit breaker rated for?\u003c\/strong\u003e The Lewmar Circuit Breaker 68000348 is rated for 50 amps.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhich Lewmar windlass models does this circuit breaker fit?\u003c\/strong\u003e This 50 amp breaker (part number 68000348) is sized for the Pro-Sport\/Pro-Fish 700W, CPX2\/V2 24V, C3 24V, VX1 300, VX2\/RX2 24V, and HX1 500 windlass models.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much does the Lewmar 68000348 circuit breaker weigh?\u003c\/strong\u003e It weighs 0.3 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat does this circuit breaker do for my windlass?\u003c\/strong\u003e It protects the windlass motor and wiring by breaking the circuit if current draw exceeds 50 amps, and it can also be used to manually disconnect power to the windlass.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan I use the 68000348 breaker on a windlass model not listed in its fitment?\u003c\/strong\u003e No. The Lewmar 68000348 50 amp breaker is matched specifically to the Pro-Sport\/Pro-Fish 700W, CPX2\/V2 24V, C3 24V, VX1 300, VX2\/RX2 24V, and HX1 500 models; using it on an unlisted model risks incorrect overcurrent protection.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs this circuit breaker resettable or does it need replacing after it trips?\u003c\/strong\u003e The Lewmar 68000348 is a circuit breaker, which is resettable after tripping, unlike a one-time-use fuse.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere does the 68000348 breaker install in the windlass wiring?\u003c\/strong\u003e It installs in the power supply line between the battery and the windlass motor, acting as both overcurrent protection and a manual disconnect switch.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat voltage systems is the Lewmar 68000348 used on?\u003c\/strong\u003e Its listed fitment includes both 12V and 24V Lewmar windlass models, including CPX2\/V2, C3, VX2\/RX2, and HX1 500, so it is used across those specific voltage configurations.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes the 50 amp rating apply to a specific windlass motor size?\u003c\/strong\u003e Yes, the 50 amp rating on part number 68000348 corresponds to the current draw of the Pro-Sport\/Pro-Fish 700W and related windlass models listed in its fitment.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the Lewmar 68000348 a genuine Lewmar part?\u003c\/strong\u003e Yes, 68000348 is the Lewmar manufacturer part number for this 50 amp circuit breaker.\u003c\/p\u003e","brand":"Lewmar","offers":[{"title":"Default Title","offer_id":49025138295003,"sku":"LEW-68000348","price":132.42,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/i_26b7e60a-dd9c-4854-ae69-83cc61561ab3.png?v=1785349683"},{"product_id":"lewmar-guarded-rocker-switch-68000593-dual-direction-12v-24v-dc-windlass-control-switch","title":"Lewmar Guarded Rocker Switch 68000593, Dual Direction 12V\/24V DC Windlass Control Switch","description":"\u003cp\u003eThe Lewmar 68000593 is a guarded dual direction rocker switch built for controlling a boat windlass from the helm, wheelhouse, or flybridge. The rocker gives clear up and down actuation for retrieving or deploying anchor, and works as either a primary helm switch or a secondary switch at a second station. A raised plastic guard surrounds the rocker to help prevent accidental activation from bumps or stray gear, reducing the risk of an unintended windlass engagement.\u003c\/p\u003e\u003cp\u003eThe switch is rated for 12 or 24 Volt DC systems at 5 Amps, using normally closed contacts with brass contact material and screw terminals for a secure electrical connection. The housing is molded plastic in black, sized to mount cleanly into a standard helm or dash panel, and carries an IP65 rating for protection against dust and water exposure in an open helm environment. It is backed by a 3 year manufacturer warranty.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Lewmar\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e 68000593\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSwitch Type:\u003c\/strong\u003e Rocker\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eControl Type:\u003c\/strong\u003e Dual direction (up\/down)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOperation Mode:\u003c\/strong\u003e ON-OFF\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNumber of Positions:\u003c\/strong\u003e 2\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOperating Voltage:\u003c\/strong\u003e 12 or 24 Volts DC\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCurrent Rating:\u003c\/strong\u003e 5 Amps\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eContact Type:\u003c\/strong\u003e Normally closed\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eContact Material:\u003c\/strong\u003e Brass\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTerminal:\u003c\/strong\u003e Screw\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector Type:\u003c\/strong\u003e Clamp\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Plastic\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e Black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInternational Protection Rating:\u003c\/strong\u003e IP65\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eItem Dimensions:\u003c\/strong\u003e 5.5 x 4.5 x 2 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 0.09375 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWarranty:\u003c\/strong\u003e 3 year manufacturer\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 743683317088\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat is the Lewmar 68000593 switch used for?\u003c\/strong\u003e The Lewmar 68000593 is a guarded rocker switch that provides dual direction up and down control for a boat windlass, letting you retrieve or deploy anchor from a helm, wheelhouse, or flybridge station.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes the Lewmar 68000593 work on both 12 volt and 24 volt boats?\u003c\/strong\u003e Yes, the 68000593 switch operates on either 12 or 24 Volt DC systems, making it compatible with most common marine electrical setups.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat amperage is the Lewmar 68000593 rated for?\u003c\/strong\u003e This switch is rated for 5 Amps, sized for control circuit switching on windlass systems that use a solenoid contactor or control box.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat does the guard on this rocker switch do?\u003c\/strong\u003e A raised plastic guard surrounds the rocker on the Lewmar 68000593 to help prevent accidental activation from bumps or stray gear at the helm.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat color is the Lewmar 68000593 rocker switch?\u003c\/strong\u003e It is finished in black, matching common marine dash and helm panels.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow big is the Lewmar 68000593 switch?\u003c\/strong\u003e The switch measures 5.5 x 4.5 x 2 inches, sized for mounting into a standard helm or dash panel.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the Lewmar 68000593 switch made of?\u003c\/strong\u003e The housing is molded plastic, with brass contact material inside for the electrical contacts.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the Lewmar 68000593 protected against water exposure at the helm?\u003c\/strong\u003e Yes, it carries an IP65 protection rating, suited to an open helm, wheelhouse, or flybridge location.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat type of electrical contacts does this switch use?\u003c\/strong\u003e The 68000593 uses normally closed contacts with screw terminals and a clamp-type connector.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes the Lewmar 68000593 come with a warranty?\u003c\/strong\u003e It is backed by a 3 year manufacturer warranty.\u003c\/p\u003e","brand":"Lewmar","offers":[{"title":"Default Title","offer_id":49025138426075,"sku":"LEW-68000593","price":88.32,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/img_afc0ac01-9fa5-45b0-a685-622ee9c7c1ba.jpg?v=1785332757"},{"product_id":"lewmar-68000917-windlass-foot-switch-white-up-direction-deck-mount","title":"Lewmar 68000917 Windlass Foot Switch, White, Up Direction, Deck Mount","description":"\u003cp\u003eThe Lewmar 68000917 is a deck-mounted foot switch used to control the up direction of a windlass, letting the operator raise the anchor hands-free while working the bow. It is built from plastic and finished in white to suit deck hardware and hull colors on most boats. A hinged cover sits over the switch face to prevent accidental operation, protecting against unintended windlass activation from foot traffic, spray, or gear left on deck. The deck mount design allows it to be installed flush at the bow station alongside a matching down-direction switch for full windlass control from the deck. As a foot switch, it is wired into the windlass control circuit and operated by foot pressure, freeing the operator's hands for line and anchor handling during retrieval. This is a genuine Lewmar part, identified by Lewmar part number 68000917, and is sold as a single switch assembly for the up function. It weighs 0.29375 pounds, making it a lightweight, low-profile deck fitting. Boat owners replacing a worn, cracked, or non-responsive foot switch, or outfitting a new windlass installation, can use this part to restore or add up-direction foot control at the deck.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Lewmar\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e 68000917\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct Type:\u003c\/strong\u003e Windlass Foot Switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFunction\/Direction:\u003c\/strong\u003e Up\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e White\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting Type:\u003c\/strong\u003e Deck Mount\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Plastic\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSpecial Feature:\u003c\/strong\u003e Hinged cover to prevent accidental operation\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 0.29375 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 743683328978\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat direction does the Lewmar 68000917 foot switch control?\u003c\/strong\u003e The Lewmar 68000917 is the up-direction foot switch, used to raise the anchor via the windlass. A separate switch is used for the down\/lower function.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat color is this foot switch?\u003c\/strong\u003e It is white, matching Lewmar's standard deck hardware finish for the 68000917 foot switch.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow is the Lewmar 68000917 mounted?\u003c\/strong\u003e This foot switch is a deck-mount unit, installed flush into the deck at the bow control station.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the foot switch made of?\u003c\/strong\u003e The 68000917 foot switch is made of plastic, suited to the marine deck environment.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes this switch have any protection against accidental activation?\u003c\/strong\u003e Yes, the Lewmar 68000917 has a hinged cover over the switch face that prevents accidental operation from foot traffic or gear on deck.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much does the foot switch weigh?\u003c\/strong\u003e The Lewmar 68000917 weighs 0.29375 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs this a genuine Lewmar part?\u003c\/strong\u003e Yes, this is a genuine Lewmar foot switch, part number 68000917.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is included with the 68000917?\u003c\/strong\u003e The listing is for the single up-direction foot switch assembly, identified by Lewmar part number 68000917.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan this foot switch be used to lower the anchor as well?\u003c\/strong\u003e No, the 68000917 is dedicated to the up function only; lowering the anchor requires the corresponding down-direction foot switch, a separate part number.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the foot switch operated by hand or foot?\u003c\/strong\u003e It is a foot-operated switch, allowing hands-free control of the windlass up function while working at the bow.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the UPC for this part?\u003c\/strong\u003e The UPC for the Lewmar 68000917 foot switch is 743683328978.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy would I need to replace this foot switch?\u003c\/strong\u003e A cracked hinged cover, worn contacts, or a foot switch that no longer engages the windlass reliably are common reasons to replace the Lewmar 68000917.\u003c\/p\u003e","brand":"Lewmar","offers":[{"title":"Default Title","offer_id":49025138393307,"sku":"LEW-68000917","price":53.56,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/img_0a67f85b-9a19-43cb-8671-29ce18174873.jpg?v=1785332741"},{"product_id":"lewmar-deck-foot-switch-68000918-windlass-down-white-12v-24v-dc","title":"Lewmar Deck Foot Switch 68000918 - Windlass Down, White, 12V\/24V DC","description":"\u003cp\u003eThe Lewmar Deck Foot Switch (68000918) is a single-direction, deck-mounted control for operating a 12V or 24V DC electric windlass. Marked for the Windlass Down function, it lets you lower the anchor hands-free by stepping on the switch, keeping both hands available for line handling on the foredeck. The switch is finished in white and built with a plastic housing designed to stand up to deck exposure.\u003c\/p\u003e\u003cp\u003eA hinged cover sits over the switch face and must be lifted before the switch can be activated, which guards against accidental windlass operation from a stray step or dropped gear. Internally the switch uses a hinge-lever actuator with a 1-way circuit and a 5 Amp contact rating, wired through screw terminals with copper contacts. It is designed to be wired into a contactor or control box rather than switching the windlass motor current directly, which is the standard setup for deck-mounted windlass controls.\u003c\/p\u003e\u003cp\u003eFor installation, the switch is designed to mount through a deck or panel cutout with a mounting hole diameter of 78 mm and a bore diameter of 9.5 mm, through a panel 7.8 mm thick, and is secured with 3 mounting screws through 3.6 mm diameter holes. Because this switch is dedicated to the Down function only, boats that need both raise and lower deck controls will require a separate Windlass Up switch as its own part.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Lewmar\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e 68000918\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSwitch Type:\u003c\/strong\u003e Foot Switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFunction:\u003c\/strong\u003e Windlass Down (single direction)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e White\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Plastic\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOperating Voltage:\u003c\/strong\u003e 12 Volt DC \/ 24 Volt DC\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCurrent Rating:\u003c\/strong\u003e 5 Amps\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCircuit Type:\u003c\/strong\u003e 1-way\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eActuator Type:\u003c\/strong\u003e Hinge Lever with Hinged Safety Cover\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting Type:\u003c\/strong\u003e Deck Mount\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting Hole Diameter:\u003c\/strong\u003e 78 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBore Diameter:\u003c\/strong\u003e 9.5 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePanel Thickness:\u003c\/strong\u003e 7.8 mm\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNumber of Mounting Holes:\u003c\/strong\u003e 3, 3.6 mm diameter each\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector Type:\u003c\/strong\u003e Screw Terminal\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eContact Material:\u003c\/strong\u003e Copper\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 0.29375 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 743683328985\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003cul\u003e\u003cli\u003eCompatible with 12 Volt DC and 24 Volt DC electric windlasses when wired through a contactor or control box.\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat does the Lewmar 68000918 foot switch control?\u003c\/strong\u003e It is the Windlass Down switch, a single-direction deck foot switch that lowers the anchor when a 12V or 24V DC electric windlass is wired to it through a contactor or control box.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes this switch also raise the windlass?\u003c\/strong\u003e No, part number 68000918 is a single-direction switch dedicated to Windlass Down only; raising the anchor requires the separate Windlass Up foot switch, which is a different Lewmar part number.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat voltage systems is the 68000918 foot switch compatible with?\u003c\/strong\u003e It is rated for both 12 Volt DC and 24 Volt DC electric windlass systems, with a 5 Amp contact rating through screw terminal connections.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat color is this foot switch?\u003c\/strong\u003e The Lewmar Deck Foot Switch 68000918 is finished in white.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow does the hinged cover work?\u003c\/strong\u003e A hinged cover sits over the switch face and must be lifted before the switch underneath can be pressed, which prevents the windlass from activating accidentally from a stray step or dropped item on deck.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat size cutout does the 68000918 need for installation?\u003c\/strong\u003e The switch mounts through a 78 mm diameter cutout with a 9.5 mm bore, fits a panel 7.8 mm thick, and is secured with 3 mounting screws through 3.6 mm diameter holes.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan this switch operate the windlass motor directly?\u003c\/strong\u003e No, the 68000918 foot switch is designed to be wired into a contactor or control box rather than switching the windlass motor's full current directly.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the foot switch housing made of?\u003c\/strong\u003e The Lewmar 68000918 foot switch has a plastic housing with copper switch contacts.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much does the Lewmar 68000918 foot switch weigh?\u003c\/strong\u003e It weighs 0.29375 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs this foot switch available in other finishes?\u003c\/strong\u003e Yes, the Windlass Down foot switch is offered in other finishes under different part numbers; 68000918 is the white version.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat type of electrical connection does this switch use?\u003c\/strong\u003e The 68000918 foot switch connects via screw terminals with copper contacts, on a 1-way circuit.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the 68000918 foot switch genuine Lewmar?\u003c\/strong\u003e Yes, part number 68000918 is a genuine Lewmar Deck Foot Switch, not an aftermarket equivalent.\u003c\/p\u003e","brand":"Lewmar","offers":[{"title":"Default Title","offer_id":49025138786523,"sku":"LEW-68000918","price":53.56,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/img_6cdf1bba-249a-480c-8ead-76b5abd41f9f.jpg?v=1785332757"},{"product_id":"anchorlift-12v-windlass-solenoid-400-amp-regular-reverse-3-4-post-motors","title":"Anchorlift 12V Windlass Solenoid, 400 Amp, Regular\/Reverse, 3 \u0026 4 Post Motors","description":"\u003cp\u003eThe Anchorlift 12V Windlass Solenoid is a compact, high-capacity switching solenoid built to operate anchor windlass systems rated from 400 to 3000 watts. It handles up to 400 amps, making it suitable for windlass motors that draw heavy current during anchor retrieval and deployment. The solenoid is configured for regular\/reverse operation, allowing it to control both the up and down directions of a windlass motor, and it is built with multiple external posts to accommodate 3 and 4 post motor wiring configurations. The external connection layout is designed for straightforward installation, giving boat owners and installers easy access to the terminals when wiring or replacing a windlass solenoid. As a 12V component, it is intended for standard 12 volt marine electrical systems commonly found on recreational boats. This solenoid is a functional replacement or upgrade part for anchor windlass installations where the existing solenoid has failed or where a windlass system is being wired from scratch. Its compact size helps it fit into the tight electrical compartments typical of windlass installations without requiring major modification to existing wiring runs.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Anchorlift\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e 90501\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupply Voltage:\u003c\/strong\u003e 12V\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaximum Motor Rating:\u003c\/strong\u003e 3000 Watts\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaximum Amperage:\u003c\/strong\u003e 400 Amps\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolenoid Type:\u003c\/strong\u003e Regular\/Reverse\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTerminal Configuration:\u003c\/strong\u003e Multiple Posts (3 and 4 Post Motors)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 2.4 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 810055911103\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat is the Anchorlift 90501 solenoid used for?\u003c\/strong\u003e The Anchorlift 90501 is a 12V windlass solenoid that switches power to an anchor windlass motor, operating systems rated from 400 to 3000 watts.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow many amps can the Anchorlift 90501 solenoid handle?\u003c\/strong\u003e Up to 400 amps, which is the maximum current rating of the Anchorlift 12V Windlass Solenoid, part number 90501.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes the 90501 solenoid support both up and down windlass operation?\u003c\/strong\u003e Yes, the Anchorlift 90501 is a regular\/reverse type solenoid, meaning it is designed to control both directions of windlass motor operation.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat voltage system is the Anchorlift 90501 solenoid designed for?\u003c\/strong\u003e It is a 12V solenoid, intended for use on standard 12 volt marine electrical systems.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the Anchorlift 90501 compatible with 3 post and 4 post windlass motors?\u003c\/strong\u003e Yes, the Anchorlift 90501 solenoid has multiple external posts, making it suitable for both 3 post and 4 post windlass motor configurations.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much does the Anchorlift windlass solenoid weigh?\u003c\/strong\u003e The Anchorlift 90501 windlass solenoid weighs 2.4 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the maximum motor wattage the 90501 solenoid can operate?\u003c\/strong\u003e 3000 watts is the maximum motor rating supported by the Anchorlift 90501 windlass solenoid.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the Anchorlift 90501 easy to install?\u003c\/strong\u003e Yes, the external connections on the Anchorlift 90501 solenoid are designed to make installation straightforward.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the UPC for the Anchorlift 90501 windlass solenoid?\u003c\/strong\u003e The UPC for the Anchorlift 90501 windlass solenoid is 810055911103.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan the Anchorlift 90501 solenoid be used as a replacement part?\u003c\/strong\u003e Yes, the 90501 is a standalone 12V windlass solenoid suitable for replacing a failed solenoid or wiring a new windlass installation rated within its 400 to 3000 watt range.\u003c\/p\u003e","brand":"Anchorlift","offers":[{"title":"Default Title","offer_id":49027427336411,"sku":"ACL-90501","price":161.77,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/Untitled-1__45554.1763741643.500.750.jpg?v=1785163279"},{"product_id":"maxwell-up-down-anchor-switch-p102938-panel-mount-windlass-remote-12v-24v-dc","title":"Maxwell Up\/Down Anchor Switch P102938 - Panel-Mount Windlass Remote, 12V\/24V DC","description":"\u003cp\u003eThe Maxwell Up\/Down Anchor Switch (P102938) is a panel-mounted remote control switch that lets you run the windlass from the helm, flying bridge, or cockpit instead of standing at the bow. It is built for use with dual-directional solenoids, so a single press sends the up or down command straight to the solenoid pack controlling the windlass motor. The switch housing is manufactured from marine-grade materials and is splash proof, so it holds up to spray and washdown in an open helm or flying bridge station without needing extra weather covers.\u003c\/p\u003e\u003cp\u003eA built-in power indicator light confirms the switch is live, and back lighting makes the up\/down positions easy to see and operate at night or in low light. The switch is wired for 12V or 24V DC systems, matching either voltage used on Maxwell dual-directional windlass solenoid setups. It comes in a black finish and is sold as a single panel-mounted unit, making it a straightforward way to add or replace remote windlass control at a second helm position or to restore up\/down function at the primary control station.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Maxwell\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e P102938\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct Type:\u003c\/strong\u003e Panel-mounted Up\/Down anchor switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVoltage:\u003c\/strong\u003e 12V or 24V DC\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatible Devices:\u003c\/strong\u003e Dual-directional windlass solenoids\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Marine-grade materials\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWater Resistance:\u003c\/strong\u003e Splash proof\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIndicator Light:\u003c\/strong\u003e Power indicator light with back lighting\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e Black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eController Type:\u003c\/strong\u003e Panel-mounted switch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUnit Count:\u003c\/strong\u003e 1 switch per pack\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 9414761049405\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 0.14 pounds\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat does the Maxwell P102938 switch do?\u003c\/strong\u003e The P102938 is a panel-mounted Up\/Down switch that lets you operate a Maxwell windlass remotely from the helm, flying bridge, or cockpit instead of the bow.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat windlass solenoids does this switch work with?\u003c\/strong\u003e P102938 is designed for use with dual-directional solenoids, sending the up or down command to the solenoid pack that drives the windlass motor.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the P102938 switch waterproof?\u003c\/strong\u003e It is splash proof and manufactured from marine-grade materials, suitable for mounting at an open helm or flying bridge station exposed to spray.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat voltage does the P102938 anchor switch use?\u003c\/strong\u003e This switch is suitable for use with 12V or 24V DC dual-directional solenoid systems.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes the switch have a light so I can see it at night?\u003c\/strong\u003e Yes, the P102938 includes a power indicator light and back lighting so the up\/down positions are visible in low light or at night.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat color is the Maxwell P102938 switch?\u003c\/strong\u003e The P102938 Up\/Down anchor switch has a black finish.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow many switches come in one order?\u003c\/strong\u003e Each order includes one Maxwell P102938 panel-mounted Up\/Down switch.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much does the P102938 switch weigh?\u003c\/strong\u003e The Maxwell Up\/Down Anchor Switch weighs 0.14 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan I install a second control station with this switch?\u003c\/strong\u003e Yes, since the P102938 is a standalone panel-mounted switch, it can be added at a second location such as a flying bridge or cockpit to control the same dual-directional solenoid setup.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes the P102938 switch include the solenoids or wiring harness?\u003c\/strong\u003e No, the P102938 is the Up\/Down control switch only; it is intended for use with a separate dual-directional solenoid pack.\u003c\/p\u003e","brand":"Maxwell Windlass","offers":[{"title":"Default Title","offer_id":49028228546779,"sku":"MAX-P102938","price":60.34,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/Untitled-1__30633.1763741580.500.750.jpg?v=1785165138"},{"product_id":"maxwell-pm-12v-solenoid-pack-sp5102-windlass-solenoid","title":"Maxwell PM 12V Solenoid Pack SP5102 Windlass Solenoid","description":"\u003cp\u003eThe Maxwell PM 12V Solenoid Pack (SP5102) is a heavy duty solenoid pack built for Maxwell windlass systems. It houses the solenoids that switch high-current power to the windlass motor, allowing the up\/down control panel, remote, or foot switches to direct motor operation without routing full motor current through the helm switch itself. This keeps switching circuits protected while delivering the amperage the windlass motor needs on demand.\u003c\/p\u003e\u003cp\u003eBuilt to a 12V DC electrical system, the solenoid pack is designed as a direct-fit component for Maxwell windlass installations that call for this solenoid pack configuration. It is supplied in a compact housing suited for mounting in a dry, accessible location near the windlass motor and control wiring, consistent with standard windlass solenoid installation practice.\u003c\/p\u003e\u003cp\u003eAs a Maxwell Marine component, the SP5102 solenoid pack is intended for boat owners maintaining, repairing, or upgrading a Maxwell windlass electrical system, and provides a straightforward replacement path when an existing solenoid pack has failed or needs servicing.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Maxwell\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e SP5102\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct Name:\u003c\/strong\u003e PM 12V Solenoid Pack\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVoltage:\u003c\/strong\u003e 12V DC\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 1.15625 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 9414761039451\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCategory:\u003c\/strong\u003e Switches \u0026amp; Solenoids\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003cp\u003eDesigned for use with Maxwell 12V windlass systems that specify the SP5102 solenoid pack.\u003c\/p\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat is the Maxwell SP5102 solenoid pack used for?\u003c\/strong\u003e The SP5102 is a heavy duty 12V solenoid pack that switches power to a Maxwell windlass motor, letting an up\/down panel, remote control, or foot switches direct motor operation without passing full motor current through the control switch.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the SP5102 a 12V or 24V solenoid pack?\u003c\/strong\u003e The SP5102 Maxwell PM Solenoid Pack is a 12V DC unit.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much does the Maxwell SP5102 solenoid pack weigh?\u003c\/strong\u003e It weighs 1.15625 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat brand is the SP5102 solenoid pack?\u003c\/strong\u003e SP5102 is a genuine Maxwell Marine part, sold as the PM 12V Solenoid Pack.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes the SP5102 solenoid pack work with a windlass control panel?\u003c\/strong\u003e Yes, the SP5102 is designed to work in conjunction with a windlass up\/down control panel, remote control, or foot switches to direct the motor's operation.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhere should the SP5102 solenoid pack be installed?\u003c\/strong\u003e Like other Maxwell windlass solenoid packs, the SP5102 should be mounted in a dry, accessible area near the windlass wiring.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the UPC for the Maxwell SP5102 solenoid pack?\u003c\/strong\u003e The UPC for the Maxwell PM 12V Solenoid Pack (SP5102) is 9414761039451.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the SP5102 a replacement part or a new installation component?\u003c\/strong\u003e The SP5102 solenoid pack can be used either to replace a failed solenoid pack on an existing Maxwell windlass or as part of a new windlass electrical installation.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes the SP5102 include mounting hardware?\u003c\/strong\u003e The dossier for the Maxwell PM 12V Solenoid Pack (SP5102) does not list included mounting hardware; it covers the solenoid pack unit itself.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the SP5102 solenoid pack genuine Maxwell Marine, or aftermarket?\u003c\/strong\u003e The SP5102 PM 12V Solenoid Pack is a genuine Maxwell Marine part, not an aftermarket equivalent.\u003c\/p\u003e","brand":"Maxwell Windlass","offers":[{"title":"Default Title","offer_id":49028228808923,"sku":"MAX-SP5102","price":252.6,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/s__02175.1763741612.500.750.jpg?v=1785165154"},{"product_id":"maxwell-sp5104-reversing-solenoid-12v-dual-direction-solenoid-pack-200-amp-continuous","title":"Maxwell SP5104 Reversing Solenoid, 12V Dual-Direction Solenoid Pack, 200+ Amp Continuous","description":"\u003cp\u003eThe Maxwell SP5104 Reversing Solenoid is a 12V dual-direction solenoid pack used in conjunction with a remote up\/down panel, an Auto Anchor 500C\/RC control, a roving hand held remote control, and\/or foot switches to switch the windlass motor in the required direction. It houses heavy-duty solenoids rated at more than 200 amps continuous, giving it the switching capacity needed for windlass motor loads. The unit is sealed in a weather proof box, though installation in a dry area is always recommended for best long-term reliability. Optional ignition protected solenoids are also available for this line. The SP5104 was formerly sold as part number P19045, so buyers replacing an older unit under that designation should order the SP5104 as its current equivalent. This solenoid pack is finished in black and built for 12V windlass control systems that need a dedicated dual-direction switching unit rather than a single-direction solenoid. It is a straightforward swap-in replacement for the same position in a Maxwell windlass control circuit.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Maxwell\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e SP5104\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 9414761131780\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVoltage:\u003c\/strong\u003e 12 Volts\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eContinuous Amp Rating:\u003c\/strong\u003e More than 200 amps continuous\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolenoid Configuration:\u003c\/strong\u003e Dual direction (reversing) solenoid pack\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEnclosure:\u003c\/strong\u003e Sealed, weather proof box\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e Black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Plastic\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePackage Dimensions:\u003c\/strong\u003e 5.0 inches x 5.0 inches x 3.0 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 1.94 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFormer Part Number:\u003c\/strong\u003e P19045\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003cp\u003eDesigned for use with a remote up\/down panel, Auto Anchor 500C\/RC control, roving hand held remote control, and\/or foot switches to control windlass motor direction.\u003c\/p\u003e\u003ch3\u003eReplaces (OEM)\u003c\/h3\u003e\u003cul\u003e\u003cli\u003eP19045\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat is the Maxwell SP5104 used for?\u003c\/strong\u003e The Maxwell SP5104 is a 12V reversing solenoid pack that switches a windlass motor in the required direction when used with a remote up\/down panel, an Auto Anchor 500C\/RC control, a hand held remote, and\/or foot switches.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the SP5104 a single solenoid or a set?\u003c\/strong\u003e The SP5104 is a solenoid pack containing dual direction, heavy-duty solenoids housed together in one weather proof box, not a single solenoid.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat amperage is the SP5104 rated for?\u003c\/strong\u003e The solenoids in the Maxwell SP5104 pack are rated at more than 200 amps continuous, which covers typical windlass motor switching loads.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the SP5104 waterproof?\u003c\/strong\u003e The SP5104 reversing solenoid is sealed in a weather proof box, though Maxwell recommends installing it in a dry location whenever possible for the longest service life.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes the SP5104 replace part number P19045?\u003c\/strong\u003e Yes, the Maxwell SP5104 was formerly sold as part number P19045, so it is the current version of that same reversing solenoid pack.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much does the SP5104 weigh?\u003c\/strong\u003e The Maxwell SP5104 reversing solenoid pack weighs 1.94 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat voltage does the SP5104 operate on?\u003c\/strong\u003e The SP5104 reversing solenoid pack is a 12V unit.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat color is the SP5104 housing?\u003c\/strong\u003e The Maxwell SP5104 solenoid pack has a black housing.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan the SP5104 be used with a foot switch instead of a panel?\u003c\/strong\u003e Yes, the SP5104 can be wired to work with foot switches, as well as a remote up\/down panel, Auto Anchor 500C\/RC control, or a roving hand held remote.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAre ignition protected versions of the SP5104 available?\u003c\/strong\u003e Optional ignition protected solenoids are available for the SP5104 reversing solenoid pack for installations where that protection is required.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat material is the SP5104 housing made from?\u003c\/strong\u003e The Maxwell SP5104 reversing solenoid pack has a plastic housing.\u003c\/p\u003e","brand":"Maxwell Windlass","offers":[{"title":"Default Title","offer_id":49028228841691,"sku":"MAX-SP5104","price":264.94,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/Untitled-1__28125.1763741579.500.750.jpg?v=1785165154"},{"product_id":"trac-outdoors-g2-anchor-winch-second-switch-kit-69040-for-fisherman-25-and-pontoon-35-winches","title":"TRAC Outdoors G2 Anchor Winch Second Switch Kit 69040 for Fisherman 25 and Pontoon 35 Winches","description":"\u003cp\u003eThe TRAC Outdoors G2 Anchor Winch Second Switch Kit (part number 69040) adds a second control point to your electric anchor winch, letting you raise and lower anchor from a helm location or anywhere else on the boat that is more convenient than the winch itself. The kit works with TRAC G2 anchor winches in both fresh and salt water models, and is specifically compatible with the TRAC Fisherman 25 and Pontoon 35 G2 electric winches. The original switch mounted on the winch cover continues to function normally after installation, so you end up with two working control points instead of one.\u003c\/p\u003e\u003cp\u003eEverything needed for the installation is included in the box: a 24 foot pre-made wiring harness with connectors on both ends, a sealed marine-grade switch, a switch plate (bezel faceplate), and four mounting screws. Installation involves removing the winch cover, disconnecting the existing switch from the control unit, connecting the wiring harness to the winch housing switch and control unit, and running the harness to your chosen second switch location. A rectangular cutout measuring 1.25 inches wide by 2.25 inches high is required to mount the new switch, with four screw holes drilled using a 1\/8 inch drill bit. If the 24 foot harness is not long enough to reach your desired location, additional wire can be spliced in; if it is too long, the excess can be coiled and secured with cable ties.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e TRAC Outdoors\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e 69040\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct Type:\u003c\/strong\u003e Anchor Winch Second Switch Kit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatible Models:\u003c\/strong\u003e TRAC G2 Fisherman 25 and Pontoon 35 anchor winches (fresh and salt water models)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eKit Includes:\u003c\/strong\u003e Sealed switch, switch plate (bezel faceplate), pre-made wiring harness with connectors, 4 mounting screws\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWiring Harness Length:\u003c\/strong\u003e 24 feet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting Cutout Size:\u003c\/strong\u003e 1.25 inches wide x 2.25 inches high\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDrill Bit Size for Screw Holes:\u003c\/strong\u003e 1\/8 inch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSwitch Type:\u003c\/strong\u003e Push button\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCircuit Type:\u003c\/strong\u003e 1-way\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting Type:\u003c\/strong\u003e Surface mount\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Plastic\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e Black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eItem Dimensions:\u003c\/strong\u003e 1.5 x 3.5 x 8.8 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 1.54375 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 666996101154\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTRAC G2 Fisherman 25 anchor winch\u003c\/li\u003e\n\u003cli\u003eTRAC G2 Pontoon 35 anchor winch\u003c\/li\u003e\n\u003cli\u003eCompatible with all TRAC G2 anchor winches, fresh and salt water models\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat comes in the TRAC G2 Anchor Winch Second Switch Kit (69040)?\u003c\/strong\u003e The kit includes a sealed marine-grade switch, a switch plate (bezel faceplate), a pre-made 24 foot wiring harness with connectors, and 4 mounting screws, so everything needed to add a second control point is in the box.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhich TRAC anchor winches work with this second switch kit?\u003c\/strong\u003e The TRAC G2 Anchor Winch Second Switch Kit 69040 is compatible with TRAC G2 anchor winches, including the Fisherman 25 and Pontoon 35 models, in both fresh and salt water versions.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan I run the anchor winch from two switches at the same time?\u003c\/strong\u003e Yes, once the 69040 kit is installed the original switch on the winch cover keeps working, so you have two independent locations from which to operate the anchor winch.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes installing the second switch disable the switch on the winch itself?\u003c\/strong\u003e No, the switch mounted on the winch cover continues to operate normally after the TRAC 69040 second switch kit is installed.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow long is the wiring harness included with this kit?\u003c\/strong\u003e The wiring harness in the TRAC G2 Anchor Winch Second Switch Kit is 24 feet long, running from the winch control unit to your chosen second switch location.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat size hole do I need to cut to mount the second switch?\u003c\/strong\u003e A rectangular cutout measuring 1.25 inches wide by 2.25 inches high is required, with four screw holes drilled using a 1\/8 inch drill bit for the mounting screws.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat if the 24 foot wiring harness is not long enough to reach my helm?\u003c\/strong\u003e If the included 24 foot harness on the 69040 kit does not reach your desired mounting location, you can splice in additional wire to extend it, or coil and cable-tie any excess if it is too long.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs this switch kit rated for saltwater use?\u003c\/strong\u003e Yes, the TRAC G2 Anchor Winch Second Switch Kit is designed to work with TRAC G2 anchor winches in both fresh and salt water models.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the second switch made of?\u003c\/strong\u003e The switch and bezel faceplate in the TRAC 69040 kit are made of plastic and finished in black.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much does the TRAC G2 Anchor Winch Second Switch Kit weigh?\u003c\/strong\u003e The TRAC G2 Anchor Winch Second Switch Kit (69040) weighs 1.54375 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDo I need to remove the winch cover to install this kit?\u003c\/strong\u003e Yes, installing the 69040 second switch requires removing the winch cover and carefully disconnecting the existing switch from the control unit before connecting the new wiring harness.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAre mounting screws included with the second switch kit?\u003c\/strong\u003e Yes, the TRAC G2 Anchor Winch Second Switch Kit includes 4 screws for attaching the switch plate at the second location.\u003c\/p\u003e","brand":"Trac Outdoor","offers":[{"title":"Default Title","offer_id":49028250796251,"sku":"TRC-69040","price":42.49,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/2__27528.1756133917.500.750.jpg?v=1785165636"},{"product_id":"trac-outdoors-gen3-anchor-winch-2nd-switch-kit-replaces-t10215-g3-fits-t10108-g3-and-t10109-g3-winches","title":"Trac Outdoors Gen3 Anchor Winch 2nd Switch Kit - Replaces T10215-G3 - Fits T10108-G3 and T10109-G3 Winches","description":"\u003cp\u003eThe Trac Outdoors Gen3 Anchor Winch 2nd Switch Kit (69043) adds a second control point for your electric anchor winch, letting you operate it from the helm or any other location you choose. The kit is designed as an auxiliary switch, not a replacement for the original control: the switch mounted on the winch cover continues to operate normally after the second switch is installed, giving you two independent ways to raise and lower the anchor.\u003c\/p\u003e\u003cp\u003eInside the kit is a sealed push-button switch, a 24 foot cable with connectors for routing to the new switch location, and 4 screws for mounting the switch plate. The switch itself is a plastic, black, push-button design rated for 12 volts DC at 40 amps, with a normally open contact and a plug-in connector for straightforward wiring to the existing winch harness. It carries an IP54 rating for protection against dust and splashing water, suiting it to the marine environment it is installed in.\u003c\/p\u003e\u003cp\u003eThis second switch kit is built specifically for Trac Outdoors Gen3 (G3) anchor winches and is compatible with the T10108-G3 Fisherman 25 Electric Anchor Winch and the T10109-G3 Pontoon 35 Electric Anchor Winch, both sold separately. It replaces the older TRAC part number T10215-G3.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Trac Outdoors\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e 69043\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatible Devices:\u003c\/strong\u003e T10108-G3 Fisherman 25 Electric Anchor Winch, T10109-G3 Pontoon 35 Electric Anchor Winch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReplaces:\u003c\/strong\u003e T10215-G3\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOperating Voltage:\u003c\/strong\u003e 12 Volts (DC)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCurrent Rating:\u003c\/strong\u003e 40 Amps\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSwitch Type:\u003c\/strong\u003e Push Button\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eContact Type:\u003c\/strong\u003e Normally Open\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnector Type:\u003c\/strong\u003e Plug In\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTerminal:\u003c\/strong\u003e Screw\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting Type:\u003c\/strong\u003e Wall mount or surface mount\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Plastic\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e Black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable Length:\u003c\/strong\u003e 24 feet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eItem Dimensions:\u003c\/strong\u003e 1 x 1 x 1 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInternational Protection Rating:\u003c\/strong\u003e IP54\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIncluded Components:\u003c\/strong\u003e Sealed switch, 24 foot cable with connectors, 4 screws\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 1.5 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 666996102151\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWarranty:\u003c\/strong\u003e 1 year manufacturer\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eT10108-G3 Fisherman 25 Electric Anchor Winch (sold separately)\u003c\/li\u003e\n\u003cli\u003eT10109-G3 Pontoon 35 Electric Anchor Winch (sold separately)\u003c\/li\u003e\n\u003cli\u003eCompatible with G3 (Gen3) anchor winch models only\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eReplaces (OEM)\u003c\/h3\u003e\u003cul\u003e\u003cli\u003eT10215-G3\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat comes in the Trac Outdoors Gen3 Anchor Winch 2nd Switch Kit (69043)?\u003c\/strong\u003e The kit includes a sealed push-button switch, a 24 foot cable with connectors, and 4 screws for mounting the switch.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhich anchor winches work with switch kit 69043?\u003c\/strong\u003e It is compatible with G3 (Gen3) anchor winch models only: the T10108-G3 Fisherman 25 Electric Anchor Winch and the T10109-G3 Pontoon 35 Electric Anchor Winch, both sold separately.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes adding the second switch kit disable the original winch cover switch?\u003c\/strong\u003e No. The switch on the winch cover continues to operate after the Trac Outdoors 69043 second switch kit is installed, giving you two working control points.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat older part number does the 69043 switch kit replace?\u003c\/strong\u003e The Trac Outdoors Gen3 2nd Switch Kit 69043 replaces the older TRAC part number T10215-G3.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow long is the cable on the 69043 second switch kit?\u003c\/strong\u003e 24 feet, allowing the second switch to be installed at the helm or another location away from the winch.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat are the electrical ratings of the switch in kit 69043?\u003c\/strong\u003e The switch is rated for 12 volts DC at 40 amps and uses a normally open contact with a plug-in connector.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs this switch kit weatherproof for marine use?\u003c\/strong\u003e The switch in the Trac Outdoors 69043 kit carries an IP54 rating for protection against dust and splashing water.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWill the 69043 second switch kit work with older, non-G3 TRAC anchor winches?\u003c\/strong\u003e No. This kit is built for G3 (Gen3) anchor winch models only, specifically the T10108-G3 and T10109-G3.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat material and color is the 69043 switch housing?\u003c\/strong\u003e The switch is plastic and black.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the mounting type for the second switch?\u003c\/strong\u003e The switch in kit 69043 uses a wall mount or surface mount installation.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes the 69043 kit include mounting hardware?\u003c\/strong\u003e Yes, 4 screws are included for mounting the switch, along with the switch itself and a 24 foot connector cable.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the warranty on the Trac Outdoors 69043 switch kit?\u003c\/strong\u003e It carries a 1 year manufacturer warranty.\u003c\/p\u003e","brand":"Trac Outdoor","offers":[{"title":"Default Title","offer_id":49028250829019,"sku":"TRC-69043","price":41.42,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/Untitled-1__21174.1763741616.500.750.jpg?v=1785165637"},{"product_id":"trac-outdoors-wireless-anchor-winch-remote-kit-69044-replaces-t10216-for-trac-g3-fisherman-25-pontoon-35-winches","title":"Trac Outdoors Wireless Anchor Winch Remote Kit 69044 (Replaces T10216) for TRAC G3 Fisherman 25 \u0026 Pontoon 35 Winches","description":"\u003cp\u003eThe Trac Outdoors Wireless Anchor Winch Remote Kit (69044) gives you push-button control of your electric anchor winch from anywhere on the boat. Instead of walking to the winch cover switch every time you need to raise or lower the anchor, this wireless remote lets you operate the winch from the helm, the cockpit, or any other spot you prefer. The remote clips into an included storage bracket that mounts on your helm or elsewhere on the vessel, so it stays secure and within reach when not in use, and you can also use it like a dash-mounted switch if you choose to keep it in one place.\u003c\/p\u003e\u003cp\u003eThis kit is built specifically for TRAC Gen3 anchor winches and is compatible with the T10108-G3 TRAC Fisherman 25 Electric Anchor Winch and the T10109-G3 TRAC Pontoon 35 Electric Anchor Winch, both of which are sold separately. It replaces the older TRAC part number T10216, so if you are upgrading an existing installation or replacing a worn-out remote, part number 69044 is the current equivalent. The original switch on the winch cover continues to function normally after installation, giving you two independent ways to control the winch.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Trac Outdoors\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e 69044\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 666996102168\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct Type:\u003c\/strong\u003e Wireless anchor winch remote kit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatibility:\u003c\/strong\u003e T10108-G3 TRAC Fisherman 25 Anchor Winch and T10109-G3 TRAC Pontoon 35 Anchor Winch (sold separately)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReplaces:\u003c\/strong\u003e T10216\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 0.8 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e Black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eController Type:\u003c\/strong\u003e Button control\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnectivity Technology:\u003c\/strong\u003e Bluetooth\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBatteries Required:\u003c\/strong\u003e 1 (non-standard battery)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIncluded Accessories:\u003c\/strong\u003e Mountable storage bracket\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWarranty:\u003c\/strong\u003e Limited 1 year\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eT10108-G3 TRAC Fisherman 25 Electric Anchor Winch (sold separately)\u003c\/li\u003e\n\u003cli\u003eT10109-G3 TRAC Pontoon 35 Electric Anchor Winch (sold separately)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eReplaces (OEM)\u003c\/h3\u003e\u003cul\u003e\u003cli\u003eT10216\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat is included in the Trac Outdoors 69044 wireless remote kit?\u003c\/strong\u003e The 69044 kit includes a wireless remote and a mountable storage bracket, giving you everything needed to add push-button anchor winch control from a location of your choice.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhich anchor winches work with part number 69044?\u003c\/strong\u003e Part number 69044 is compatible with the T10108-G3 TRAC Fisherman 25 Electric Anchor Winch and the T10109-G3 TRAC Pontoon 35 Electric Anchor Winch, both sold separately.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes 69044 replace an older TRAC part number?\u003c\/strong\u003e Yes, 69044 replaces the older TRAC part number T10216 and is the current wireless remote kit for compatible Gen3 winches.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan the remote be mounted at the helm?\u003c\/strong\u003e Yes, the wireless remote clips into an included storage bracket that can be mounted on the helm or anywhere else on the boat.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs winch control wired or wireless with this kit?\u003c\/strong\u003e The 69044 kit is fully wireless, using push-button operation rather than a hardwired switch connection.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much does the 69044 remote kit weigh?\u003c\/strong\u003e The Trac Outdoors 69044 wireless remote kit weighs 0.8 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat color is the wireless remote kit?\u003c\/strong\u003e The 69044 remote and its storage bracket are black.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes the wireless remote require batteries?\u003c\/strong\u003e Yes, the 69044 remote requires 1 non-standard battery, which is included with the kit.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs a warranty included with the 69044 remote kit?\u003c\/strong\u003e The 69044 wireless remote kit carries a limited 1 year warranty.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDo I have to leave the remote mounted, or can I carry it around the boat?\u003c\/strong\u003e You can use the 69044 remote anywhere on the boat, or clip it into its bracket and use it like a fixed dash-mounted switch.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWill the 69044 remote work with the TRAC Angler 30 or Deckboat 40 winches?\u003c\/strong\u003e No, part number 69044 is built for the T10108-G3 Fisherman 25 and T10109-G3 Pontoon 35 winches; the Angler 30 and Deckboat 40 use a separate second-switch kit.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes adding the 69044 wireless remote disable the winch cover switch?\u003c\/strong\u003e No, the original switch on the winch cover continues to operate normally after the 69044 wireless remote kit is installed.\u003c\/p\u003e","brand":"Trac Outdoor","offers":[{"title":"Default Title","offer_id":49028251320539,"sku":"TRC-69044","price":70.64,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/69044__62575.1755183144.500.750.jpg?v=1785165637"},{"product_id":"trac-outdoors-g3-autodeploy-anchor-winch-2nd-switch-kit-fits-t10208-g3-angler-30-t10219-g3-deckboat-40-replaces-t10217-g3","title":"Trac Outdoors G3 AutoDeploy Anchor Winch 2nd Switch Kit, Fits T10208-G3 Angler 30 \u0026 T10219-G3 Deckboat 40, Replaces T10217-G3","description":"\u003cp\u003eThe Trac Outdoors G3 AutoDeploy Anchor Winch 2nd Switch Kit (69045) makes it easy to add a second, auxiliary control point for your TRAC AutoDeploy anchor winch. Instead of running back to the primary helm switch every time you need to raise, lower, or auto-deploy your anchor, this kit lets you install a fully functional second switch anywhere on the boat that is convenient for you.\u003c\/p\u003e\u003cp\u003eThe switch uses 3-button operation covering Up, Down, and Auto Deploy, giving you the same full range of control at the second location as you have at the primary switch. The control panel measures 2.5 inches x 2.9 inches and connects via a 24 foot wiring harness, giving you flexibility in where you mount the auxiliary switch relative to the winch and primary controls. The kit ships complete with everything needed for the install: a sealed switch, a bezel faceplate, cables with connectors, and 4 mounting screws, so no separate hardware purchase is required.\u003c\/p\u003e\u003cp\u003eThis 2nd Switch Kit is designed specifically for the TRAC T10208-G3 Angler 30 Anchor Winch and the TRAC T10219-G3 Deckboat 40 Anchor Winch (each sold separately). It replaces the older TRAC part number T10217-G3, so it is the correct current-production upgrade or replacement if you are working from that earlier part number.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Trac Outdoors\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e 69045\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct UPC:\u003c\/strong\u003e 666996102175\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSwitch Configuration:\u003c\/strong\u003e 3-button (Up \/ Down \/ Auto Deploy)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eControl Panel Dimensions:\u003c\/strong\u003e 2.5 inches x 2.9 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWiring Harness Length:\u003c\/strong\u003e 24 feet\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 1.5 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eKit Includes:\u003c\/strong\u003e Sealed switch, bezel faceplate, cables with connectors, 4 screws\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatible Winches:\u003c\/strong\u003e TRAC T10208-G3 Angler 30 Anchor Winch, TRAC T10219-G3 Deckboat 40 Anchor Winch\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTRAC T10208-G3 Angler 30 Anchor Winch (sold separately)\u003c\/li\u003e\n\u003cli\u003eTRAC T10219-G3 Deckboat 40 Anchor Winch (sold separately)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eReplaces (OEM)\u003c\/h3\u003e\u003cul\u003e\u003cli\u003eT10217-G3\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat anchor winches is the Trac Outdoors 69045 switch kit compatible with?\u003c\/strong\u003e The 69045 2nd Switch Kit is compatible with the TRAC T10208-G3 Angler 30 Anchor Winch and the TRAC T10219-G3 Deckboat 40 Anchor Winch, both sold separately.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes the 69045 kit replace an older TRAC part number?\u003c\/strong\u003e Yes, the Trac Outdoors 69045 2nd Switch Kit replaces the older TRAC part number T10217-G3.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is included in the box with the 69045 2nd Switch Kit?\u003c\/strong\u003e The kit includes a sealed switch, a bezel faceplate, cables with connectors, and 4 mounting screws, everything needed to install the auxiliary switch.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow many buttons does the second switch have and what do they control?\u003c\/strong\u003e The 69045 switch uses 3-button operation for Up, Down, and Auto Deploy, matching the control options of the primary switch.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow long is the wiring harness on the 69045 switch kit?\u003c\/strong\u003e The wiring harness supplied with the Trac Outdoors 69045 2nd Switch Kit is 24 feet long, allowing the auxiliary switch to be mounted well away from the winch.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat are the dimensions of the second switch control panel?\u003c\/strong\u003e The control panel on the 69045 kit measures 2.5 inches by 2.9 inches.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan I add a second switch location to my existing anchor winch setup?\u003c\/strong\u003e Yes, that is the purpose of the 69045 kit: it adds a fully functional auxiliary switch location to a TRAC T10208-G3 Angler 30 or T10219-G3 Deckboat 40 Anchor Winch that already has a primary switch.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much does the 69045 2nd Switch Kit weigh?\u003c\/strong\u003e The Trac Outdoors 69045 2nd Switch Kit weighs 1.5 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the 69045 kit the same as the TRAC wireless remote kit?\u003c\/strong\u003e No. The 69045 is a hardwired second switch kit for the T10208-G3 Angler 30 and T10219-G3 Deckboat 40 winches, which is a different product from the TRAC wireless remote kit designed for the T10108-G3 Fisherman 25 and T10109-G3 Pontoon 35 winches.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWill the 69045 switch kit work with the TRAC Fisherman 25 or Pontoon 35 anchor winches?\u003c\/strong\u003e No, the 69045 2nd Switch Kit is designed for the T10208-G3 Angler 30 and T10219-G3 Deckboat 40 Anchor Winches, not the Fisherman 25 or Pontoon 35 models.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat UPC is associated with the Trac Outdoors 69045 switch kit?\u003c\/strong\u003e The Trac Outdoors 69045 2nd Switch Kit carries UPC 666996102175.\u003c\/p\u003e","brand":"Trac Outdoor","offers":[{"title":"Default Title","offer_id":49028251353307,"sku":"TRC-69045","price":40.96,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/Untitled-1__16244.1763741616.500.750.jpg?v=1785165636"},{"product_id":"trac-isolator-bolts-4-pack-316-stainless-steel-mounting-bolts-for-anchor-winches-and-trolling-motors","title":"TRAC Isolator Bolts, 4-Pack, 316 Stainless Steel Mounting Bolts for Anchor Winches and Trolling Motors","description":"\u003cp\u003eThe TRAC Isolator Bolts 4-Pack gives you a simple way to mount an anchor winch, trolling motor, or other deck accessory from the top of your boat deck when you cannot reach underneath it. Each bolt is machined from marine-grade 316 stainless steel, which resists corrosion in both fresh and saltwater environments, so the hardware holds up to long-term exposure on the water. The isolator design helps protect your boat from vibration transferred by the mounted accessory, keeping the installation quieter and reducing wear over time. Installation is straightforward: each bolt installs into a 1\/2 inch hole using a Phillips head screwdriver, with no specialized tools required. This set includes 4 isolator bolts, making it suited to smaller installations or projects where fewer mounting points are needed; a matching 8-pack is available separately for larger jobs. The compact package weighs 0.3875 pounds. Whether you are mounting a new anchor winch or replacing worn isolator hardware on an existing accessory, this 4-pack provides corrosion-resistant, vibration-dampening bolts built for marine use.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e TRAC\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e 69060\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e 316 Stainless Steel\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePack Quantity:\u003c\/strong\u003e 4 isolator bolts\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstallation Hole Size:\u003c\/strong\u003e 1\/2 inch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDrive Type:\u003c\/strong\u003e Phillips head\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e Black oxide\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePackage Dimensions:\u003c\/strong\u003e 3.8 x 1.5 x 8.3 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 0.3875 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 666996100751\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat is included in the TRAC Isolator Bolts 4-Pack?\u003c\/strong\u003e The package contains 4 isolator bolts made from 316 stainless steel, sized to install in a 1\/2 inch hole.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat material are these bolts made from?\u003c\/strong\u003e TRAC Isolator Bolts (part number 69060) are made from marine-grade 316 stainless steel for corrosion resistance in fresh or saltwater.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat size hole do I need to install the bolts?\u003c\/strong\u003e Each bolt in the TRAC 69060 4-pack installs into a 1\/2 inch hole.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat tool is needed for installation?\u003c\/strong\u003e A Phillips head screwdriver is all that is required to install the TRAC Isolator Bolts.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the difference between the 4-pack and the 8-pack version?\u003c\/strong\u003e The 4-pack (TRAC 69060) includes 4 isolator bolts, while the 8-pack version includes 8 bolts for installations that need more mounting points.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan these bolts be used in saltwater?\u003c\/strong\u003e Yes, the 316 stainless steel construction of the TRAC Isolator Bolts is designed to resist corrosion in both fresh and saltwater.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat accessories can be mounted using these bolts?\u003c\/strong\u003e The TRAC Isolator Bolts are intended for mounting anchor winches, trolling motors, and other deck-mounted accessories.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much does the TRAC Isolator Bolts 4-Pack weigh?\u003c\/strong\u003e The 4-pack weighs 0.3875 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDo I need access underneath the deck to install these bolts?\u003c\/strong\u003e No, the TRAC Isolator Bolts are designed to be installed from the top of the boat deck, which is useful when the underside of the deck is not accessible.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat purpose does the isolator design serve?\u003c\/strong\u003e The isolator bolts help protect the boat from vibrations generated by mounted equipment such as an anchor winch or trolling motor.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat are the package dimensions of the TRAC 69060 bolt set?\u003c\/strong\u003e The 4-pack package measures 3.8 x 1.5 x 8.3 inches.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat finish do the bolts have?\u003c\/strong\u003e The TRAC Isolator Bolts have a black oxide finish.\u003c\/p\u003e","brand":"Trac Outdoor","offers":[{"title":"Default Title","offer_id":49028251386075,"sku":"TRC-69060","price":22.23,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/trc-t10075_lg__80802.1558172447.500.750.jpg?v=1785165636"},{"product_id":"trac-69061-isolator-bolts-8-pack-316-stainless-steel-deck-mounting-bolts","title":"TRAC 69061 Isolator Bolts, 8-Pack, 316 Stainless Steel Deck Mounting Bolts","description":"\u003cp\u003eThe TRAC Isolator Bolts (part number 69061) are a set of 8 marine-grade 316 stainless steel bolts designed for mounting deck accessories such as anchor winches and trolling motors directly from the top of the boat deck. Because installation happens from above, there is no need to reach underneath the deck to secure hardware, which makes the job faster and more accessible on boats where under-deck space is tight or hard to access. Beyond simple mounting, these bolts are engineered to protect the boat from vibrations transmitted by deck-mounted accessories, helping isolate movement and reduce wear on both the hardware and the surrounding deck structure over time.\u003c\/p\u003e\u003cp\u003eEach bolt is sized for a standard 1\/2 inch mounting hole and is installed with a Phillips head screwdriver, keeping the installation process straightforward with common tools. The 316-grade stainless steel construction is chosen specifically for its corrosion resistance, making this bolt set suitable for both freshwater and saltwater environments where lesser fasteners would rust or degrade. This 8-pack provides enough bolts for a full accessory installation in one purchase.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e TRAC\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e 69061\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePackage Quantity:\u003c\/strong\u003e 8 bolts\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThread Size:\u003c\/strong\u003e 1\/2 inch-13 UNC\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e 316 stainless steel\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHead Type:\u003c\/strong\u003e Phillips\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInstallation Hole Size:\u003c\/strong\u003e 1\/2 inch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eItem Dimensions:\u003c\/strong\u003e 0.92 x 0.92 x 0.63 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 0.73125 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 666996100768\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCorrosion Resistance:\u003c\/strong\u003e Marine-grade, suitable for fresh or saltwater use\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWarranty:\u003c\/strong\u003e 1 year manufacturer warranty\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat are TRAC 69061 Isolator Bolts used for?\u003c\/strong\u003e These bolts are used to mount deck accessories, such as anchor winches and trolling motors, from the top of the boat deck while also isolating vibration between the accessory and the hull.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow many bolts come in this pack?\u003c\/strong\u003e The TRAC 69061 set includes 8 isolator bolts, enough for a full accessory mounting installation.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat size hole do I need to install these bolts?\u003c\/strong\u003e A standard 1\/2 inch hole is required to install the TRAC 69061 isolator bolts.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat tool do I need to install these bolts?\u003c\/strong\u003e The bolts are installed with a Phillips head screwdriver, so no specialized tools are required for the TRAC 69061 isolator bolt installation.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat material are the TRAC 69061 bolts made from?\u003c\/strong\u003e They are made from marine-grade 316 stainless steel, chosen for its corrosion resistance in marine environments.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eAre these bolts safe to use in saltwater?\u003c\/strong\u003e Yes, the 316 stainless steel construction of the TRAC 69061 isolator bolts is suitable for both freshwater and saltwater use.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the thread size of these bolts?\u003c\/strong\u003e The TRAC 69061 isolator bolts use a 1\/2 inch-13 UNC thread.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan these bolts be installed without accessing the underside of the deck?\u003c\/strong\u003e Yes, the TRAC 69061 isolator bolts are designed to be installed entirely from the top of the boat deck, which is useful when the underside of the deck is difficult to reach.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat accessories can be mounted with these bolts?\u003c\/strong\u003e The TRAC 69061 isolator bolts are commonly used for mounting anchor winches, trolling motors, and other deck-mounted accessories.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much do these bolts weigh?\u003c\/strong\u003e The 8-pack of TRAC 69061 isolator bolts weighs 0.73125 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs there a smaller pack size available?\u003c\/strong\u003e TRAC also offers these isolator bolts in a 4-pack version for installations that require fewer bolts than the 8-pack of part 69061.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs there a warranty on these bolts?\u003c\/strong\u003e The TRAC 69061 isolator bolts are backed by a 1 year manufacturer warranty.\u003c\/p\u003e","brand":"Trac Outdoor","offers":[{"title":"Default Title","offer_id":49028251451611,"sku":"TRC-69061","price":38.32,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/trc-10076_lg__56454.1558172475.500.750.jpg?v=1785165636"},{"product_id":"trac-outdoor-anchor-winch-mounting-plate-for-anchorzone-20-and-strikezone-25-winches-part-69070","title":"Trac Outdoor Anchor Winch Mounting Plate for AnchorZone 20 and StrikeZone 25 Winches, Part 69070","description":"\u003cp\u003eThe Trac Outdoor Anchor Winch Mounting Plate, part number 69070, is a purpose-built mounting base for the T10098 AnchorZone 20 and T10100 StrikeZone 25 anchor winches. It gives installers a choice of an extended or compact position for the anchor roller, so the winch can be set up to match the bow layout of the boat. The plate is machined from aircraft aluminum and finished in a sand blasted, anodized gunmetal gray, built to hold up under continued exposure to sun, spray, and saltwater without breaking down.\u003c\/p\u003e\u003cp\u003eInstallation hardware is stainless steel and is included with the plate. An extra hole is machined into the plate that can be used for battery wire routing in some installations, keeping wiring runs cleaner at the bow. The plate is also designed to work with a range of Trac Outdoor mounting accessories, including the 90 degree and 12 degree transom and side mounts, the quick-release plate, and the spacer-pedestal, giving owners flexibility in how the winch is finally mounted to the boat. This lets an AnchorZone 20 or StrikeZone 25 owner adapt the winch mount to a transom, side rail, or pedestal setup using the same base plate.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Trac Outdoor\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e 69070\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e Anodized Gunmetal Gray\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Aircraft Aluminum\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHardware Included:\u003c\/strong\u003e Stainless Steel Hardware\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePlate Thickness:\u003c\/strong\u003e 0.4 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eForward Installation Holes:\u003c\/strong\u003e 8 Module Installation Holes\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRear Installation Holes:\u003c\/strong\u003e 8 Module Installation Holes\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSpecial Feature:\u003c\/strong\u003e Extra Hole for Battery Wire Routing (some installations)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePackage Dimensions:\u003c\/strong\u003e 11.97 x 7.6 x 0.47 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 2 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 666996101918\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eT10098 AnchorZone 20 Anchor Winch\u003c\/li\u003e\n\u003cli\u003eT10100 StrikeZone 25 Anchor Winch\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eCompatible with the T10194 90 degree transom and side mount, T10195 12 degree transom and side mount, T10196 quick-release plate, and T10197 spacer-pedestal.\u003c\/p\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat anchor winches does the Trac Outdoor 69070 mounting plate fit?\u003c\/strong\u003e The 69070 mounting plate is built for the T10098 AnchorZone 20 and T10100 StrikeZone 25 anchor winches and is not listed as compatible with other Trac Outdoor winch models.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan I mount the anchor roller in more than one position with this plate?\u003c\/strong\u003e Yes, the 69070 mounting plate offers both an extended and a compact position for the anchor roller, so it can be set up to match the bow layout of the boat.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the 69070 plate made of?\u003c\/strong\u003e It is machined from aircraft aluminum and finished with a sand blasted, anodized gunmetal gray coating for corrosion resistance.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes the mounting plate come with hardware?\u003c\/strong\u003e Stainless steel hardware is included with the Trac Outdoor 69070 anchor winch mounting plate.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow thick is the mounting plate?\u003c\/strong\u003e The plate is 0.4 inches thick, with 8 module installation holes in the forward position and 8 in the rear position.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat does the 69070 plate weigh?\u003c\/strong\u003e The Trac Outdoor 69070 mounting plate weighs 2 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs this plate compatible with the quick-release anchor mount?\u003c\/strong\u003e Yes, the 69070 mounting plate works with the T10196 quick-release plate, along with the T10194 90 degree transom and side mount, T10195 12 degree transom and side mount, and T10197 spacer-pedestal.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs there a way to route battery wiring through this plate?\u003c\/strong\u003e The 69070 plate includes an extra hole that can be used for battery wire routing in some installations.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the difference between the 69070 plate and the Gen3 mounting plate?\u003c\/strong\u003e The 69070 plate is sized for the T10098 AnchorZone 20 and T10100 StrikeZone 25 winches, while the separate Gen3 mounting plate (a different part number) is made for the Gen3 series of Trac Outdoor anchor winches instead.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is included when I order the 69070 mounting plate?\u003c\/strong\u003e The order includes the anodized gunmetal gray aircraft aluminum mounting plate along with the stainless steel mounting hardware.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the Trac Outdoor 69070 plate genuine manufacturer hardware?\u003c\/strong\u003e Yes, the 69070 is the manufacturer part number for this Trac Outdoor anchor winch mounting plate, not an aftermarket copy.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat are the overall package dimensions of the 69070 mounting plate?\u003c\/strong\u003e The 69070 mounting plate ships in a package measuring 11.97 x 7.6 x 0.47 inches.\u003c\/p\u003e","brand":"Trac Outdoor","offers":[{"title":"Default Title","offer_id":49028251484379,"sku":"TRC-69070","price":94.25,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/Untitled-1__13162.1763741616.500.750.jpg?v=1785165637"},{"product_id":"trac-69075-anchor-winch-quick-release-mount-aircraft-aluminum-fits-t10191-t10192-t10193-g3-mounting-plates-and-t10194-t10195-transom-mounts","title":"TRAC 69075 Anchor Winch Quick-Release Mount, Aircraft Aluminum, Fits T10191\/T10192\/T10193-G3 Mounting Plates and T10194\/T10195 Transom Mounts","description":"\u003cp\u003eThe TRAC 69075 Anchor Winch Quick-Release Mount is a base plate that lets you detach an electric anchor winch from its installed mount for secure storage, without removing the mount hardware itself. It is machined from aircraft aluminum, then sand blasted and anodized in gunmetal gray for a corrosion-resistant finish suited to fresh and salt water use. The quick-release design means the winch itself can be pulled off the boat and stowed below or at home, while the mount stays permanently fixed at the bow or transom, ready for the winch to be dropped back in when needed.\u003c\/p\u003e\u003cp\u003eThis mount is built for versatility: it is compatible with TRAC's T10191, T10192, and T10193-G3 mounting plates, as well as the T10194 90 degree transom and side mount, the T10195 12 degree transom and side mount, and the T10197 spacer-pedestal. That range lets it work across bow, transom, and side-mount installations depending on how the rest of the TRAC mounting system is configured. Stainless steel hardware is included for installation.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e TRAC\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e 69075\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct Type:\u003c\/strong\u003e Anchor Winch Quick-Release Mount\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e Anodized Gunmetal Gray\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSurface Treatment:\u003c\/strong\u003e Sand Blasted\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Aircraft Aluminum\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHardware Included:\u003c\/strong\u003e Stainless Steel\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStorage Feature:\u003c\/strong\u003e Mount separates from winch for secure storage\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatible Mounting Plates:\u003c\/strong\u003e T10191, T10192, T10193-G3\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatible Transom and Side Mounts:\u003c\/strong\u003e T10194 (90 Degree), T10195 (12 Degree)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatible Spacer-Pedestal:\u003c\/strong\u003e T10197\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct Dimensions:\u003c\/strong\u003e 6.51 x 6.01 x 1.76 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 30 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 666996101963\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003cp\u003eCompatible with TRAC T10191 Mounting Plate, T10192 Mounting Plate, T10193-G3 Mounting Plate, T10194 90 Degree Transom and Side Mount, T10195 12 Degree Transom and Side Mount, and T10197 Spacer-Pedestal.\u003c\/p\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat does the TRAC 69075 Quick-Release Mount do?\u003c\/strong\u003e It lets an electric anchor winch be detached from its installed base plate for secure storage, while the TRAC 69075 mount itself stays fixed in place on the boat.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat material is the TRAC 69075 mount made from?\u003c\/strong\u003e It is machined from aircraft aluminum, then sand blasted and anodized in a gunmetal gray finish for corrosion resistance.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhich mounting plates work with the 69075 quick-release mount?\u003c\/strong\u003e The TRAC 69075 is compatible with the T10191 Mounting Plate, T10192 Mounting Plate, and T10193-G3 Mounting Plate.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes the 69075 work with a transom mount?\u003c\/strong\u003e Yes, it is compatible with the T10194 90 degree transom and side mount and the T10195 12 degree transom and side mount.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan the 69075 be used with a spacer or pedestal?\u003c\/strong\u003e Yes, it is compatible with the TRAC T10197 Spacer-Pedestal for raised installations.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs mounting hardware included with the 69075?\u003c\/strong\u003e Yes, stainless steel hardware is included with the TRAC 69075 Quick-Release Mount.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much does the TRAC 69075 mount weigh?\u003c\/strong\u003e The TRAC 69075 Anchor Winch Quick-Release Mount weighs 30 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat are the dimensions of the 69075 mount?\u003c\/strong\u003e The mount measures 6.51 x 6.01 x 1.76 inches.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the 69075 mount suitable for saltwater use?\u003c\/strong\u003e Its anodized gunmetal gray, sand blasted aircraft aluminum construction is built for corrosion resistance in marine environments.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes the TRAC 69075 include the anchor winch itself?\u003c\/strong\u003e No, the 69075 is the quick-release mount only; it is designed to accept a separately installed TRAC anchor winch.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the UPC for the TRAC 69075 mount?\u003c\/strong\u003e The TRAC 69075 Anchor Winch Quick-Release Mount has UPC 666996101963.\u003c\/p\u003e","brand":"Trac Outdoor","offers":[{"title":"Default Title","offer_id":49028251517147,"sku":"TRC-69075","price":162.18,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/TRC-T10196__79398.1739462755.500.750.jpg?v=1785165642"},{"product_id":"trac-69074-anchor-winch-transom-side-mount-12-degree-angled-aircraft-aluminum-bracket","title":"TRAC 69074 Anchor Winch Transom \u0026 Side Mount, 12 Degree Angled Aircraft Aluminum Bracket","description":"\u003cp\u003eThe TRAC 69074 Anchor Winch Transom \u0026amp; Side Mount is a 12 degree angled mounting bracket that lets you install a TRAC electric anchor winch on the transom or an elevated bow location. It is machined from aircraft aluminum, then sand blasted and anodized in a gunmetal gray finish for a durable, corrosion-resistant surface. The bracket includes 8 holes sized to fit TRAC modules and cannon mounts, plus 4 holes sized to fit TRAC pot puller and scotty mounts, giving it broad compatibility with existing deck hardware patterns. Stainless steel mounting hardware is included, so no separate hardware purchase is needed for the bracket itself.\u003c\/p\u003e\u003cp\u003eThis mount is designed to pair with several TRAC mounting plates and accessories, including the T10191 Mounting Plate, T10192 Mounting Plate, T10193 G3 Mounting Plate, T10196 Quick-Release Plate, T10197 Spacer-Pedestal, and the T10250 TRAC Line Hauler\/Pot Puller (mounting plate or accessory sold separately). Its 12 degree angle is intended for transom or side mount installations where that specific angle is required for proper winch operation and rope routing.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e TRAC\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e 69074\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct Type:\u003c\/strong\u003e Anchor Winch Transom \u0026amp; Side Mount\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAngle:\u003c\/strong\u003e 12 Degrees\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Aircraft Aluminum\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e Anodized Gunmetal Gray, Sand Blasted\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting Holes:\u003c\/strong\u003e 8 Holes Fit TRAC Modules and Cannon Mounts; 4 Holes Fit TRAC Pot Puller and Scotty Mounts\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHardware Included:\u003c\/strong\u003e Stainless Steel\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatible With:\u003c\/strong\u003e T10191 Mounting Plate, T10192 Mounting Plate, T10193 G3 Mounting Plate, T10196 Quick-Release Plate, T10197 Spacer-Pedestal, T10250 TRAC Line Hauler\/Pot Puller\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 2.6 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct Dimensions:\u003c\/strong\u003e 5.25 x 6.5 x 6.38 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 666996101956\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003cp\u003eCompatible with TRAC mounting plates and accessories: T10191 Mounting Plate, T10192 Mounting Plate, T10193 G3 Mounting Plate, T10196 Quick-Release Plate, T10197 Spacer-Pedestal, and T10250 TRAC Line Hauler\/Pot Puller.\u003c\/p\u003e\u003ch3\u003eReplaces (OEM)\u003c\/h3\u003e\u003cp\u003eNo OEM cross-reference numbers apply to this part.\u003c\/p\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat angle is the TRAC 69074 anchor winch mount?\u003c\/strong\u003e The TRAC 69074 Anchor Winch Transom \u0026amp; Side Mount is angled at 12 degrees, designed for transom or side mount winch installations at that specific angle.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat material is the 69074 mount made from?\u003c\/strong\u003e It is machined from aircraft aluminum, then sand blasted and anodized in a gunmetal gray finish for corrosion resistance.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes the 69074 mount include hardware?\u003c\/strong\u003e Yes, stainless steel mounting hardware is included with the TRAC 69074 Transom \u0026amp; Side Mount.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhich TRAC mounting plates work with this bracket?\u003c\/strong\u003e The 69074 mount is compatible with the T10191 Mounting Plate, T10192 Mounting Plate, T10193 G3 Mounting Plate, T10196 Quick-Release Plate, T10197 Spacer-Pedestal, and T10250 TRAC Line Hauler\/Pot Puller.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs a mounting plate included with the 69074?\u003c\/strong\u003e No, the TRAC 69074 Transom \u0026amp; Side Mount is the bracket only; compatible mounting plates such as the T10191, T10192, or T10193 G3 are sold separately.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow many mounting holes does the 69074 bracket have?\u003c\/strong\u003e It has 8 holes sized to fit TRAC modules and cannon mounts, plus 4 additional holes sized to fit TRAC pot puller and scotty mounts.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much does the TRAC 69074 mount weigh?\u003c\/strong\u003e The TRAC 69074 Anchor Winch Transom \u0026amp; Side Mount weighs 2.6 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat are the dimensions of the 69074 mount?\u003c\/strong\u003e The TRAC 69074 measures 5.25 x 6.5 x 6.38 inches.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan the 69074 be used with a quick-release plate?\u003c\/strong\u003e Yes, the 69074 mount is compatible with the T10196 Quick-Release Plate for easy removal and storage of the winch assembly.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the difference between the 12 degree and 90 degree TRAC side mounts?\u003c\/strong\u003e The TRAC 69074 is the 12 degree angled Transom \u0026amp; Side Mount, while the T10194 is a 90 degree Transom and Side Mount; each provides a different mounting angle for different bow or transom configurations.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the 69074 mount finished to resist corrosion?\u003c\/strong\u003e Yes, it is sand blasted and anodized in a gunmetal gray finish over aircraft aluminum for durability in marine environments.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the UPC for the TRAC 69074 mount?\u003c\/strong\u003e The TRAC 69074 Anchor Winch Transom \u0026amp; Side Mount has UPC 666996101956.\u003c\/p\u003e","brand":"Trac Outdoor","offers":[{"title":"Default Title","offer_id":49028251549915,"sku":"TRC-69074","price":72.84,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/TRC-T10195__44796.1722487272.500.750.jpg?v=1785165642"},{"product_id":"trac-69076-anchor-winch-mount-spacer-pedestal-1-inch-riser-aircraft-aluminum","title":"TRAC 69076 Anchor Winch Mount Spacer\/Pedestal, 1-Inch Riser, Aircraft Aluminum","description":"\u003cp\u003eThe TRAC 69076 Anchor Winch Mount Spacer\/Pedestal is a 1-inch riser designed to raise an electric anchor winch installation for better clearance and positioning on the bow or transom. It is machined from aircraft aluminum and finished with a sand blasted, anodized gunmetal gray coating for a durable, corrosion-resistant surface. All necessary stainless steel mounting hardware is included, so no separate hardware purchase is required.\u003c\/p\u003e\u003cp\u003eThis spacer\/pedestal is built to work with TRAC's broader anchor winch mounting system, giving installers flexibility to combine it with different mounting plates and transom or side mounts depending on the boat's layout. It is compatible with the T10191 Mounting Plate, T10192 Mounting Plate, T10193 G3 Mounting Plate, T10194 90 Degree Transom and Side Mount, T10195 12 Degree Transom and Side Mount, and the T10196 Quick-Release Plate. This makes it a useful accessory for boat owners who need extra height or a different mounting angle for their anchor winch setup without replacing the entire mount.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e TRAC\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e 69076\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct Type:\u003c\/strong\u003e Anchor Winch Mount Spacer\/Pedestal\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRiser Height:\u003c\/strong\u003e 1 inch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Aircraft aluminum body, stainless steel hardware\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e Anodized gunmetal gray, sand blasted\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 30 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 666996101970\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHardware Included:\u003c\/strong\u003e Stainless steel mounting hardware\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eCompatible With\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eT10191 Mounting Plate\u003c\/li\u003e\n\u003cli\u003eT10192 Mounting Plate\u003c\/li\u003e\n\u003cli\u003eT10193 G3 Mounting Plate\u003c\/li\u003e\n\u003cli\u003eT10194 90 Degree Transom and Side Mount\u003c\/li\u003e\n\u003cli\u003eT10195 12 Degree Transom and Side Mount\u003c\/li\u003e\n\u003cli\u003eT10196 Quick-Release Plate\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat is the TRAC 69076 Anchor Winch Mount Spacer\/Pedestal used for?\u003c\/strong\u003e It is a spacer\/pedestal that adds a 1-inch riser to raise an anchor winch mounting installation, giving more clearance and positioning flexibility on a bow or transom mount.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much riser height does the 69076 spacer add?\u003c\/strong\u003e The TRAC 69076 adds a 1-inch riser to the anchor winch mount installation.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the 69076 spacer\/pedestal made of?\u003c\/strong\u003e It is machined from aircraft aluminum with a sand blasted, anodized gunmetal gray finish, and it includes stainless steel mounting hardware.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes the TRAC 69076 come with mounting hardware?\u003c\/strong\u003e Yes, all necessary stainless steel hardware is included with the TRAC 69076 Anchor Winch Mount Spacer\/Pedestal.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhich mounting plates work with the 69076 spacer\/pedestal?\u003c\/strong\u003e The 69076 is compatible with the T10191 Mounting Plate, T10192 Mounting Plate, and T10193 G3 Mounting Plate.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan the TRAC 69076 be used with a quick-release plate?\u003c\/strong\u003e Yes, the 69076 spacer\/pedestal is compatible with the T10196 Quick-Release Plate.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the TRAC 69076 compatible with transom and side mounts?\u003c\/strong\u003e It is compatible with both the T10194 90 Degree Transom and Side Mount and the T10195 12 Degree Transom and Side Mount.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the difference between the TRAC 69076 and the TRAC 69075?\u003c\/strong\u003e The TRAC 69075 is a quick-release mount that can be separated from the winch for storage and is compatible with the T10191, T10192, T10193, T10194, and T10195 mounting components. The TRAC 69076 is a fixed 1-inch riser spacer\/pedestal that additionally lists compatibility with the T10196 Quick-Release Plate; the two are separate SKUs designed for different mounting needs.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat finish does the TRAC 69076 spacer have?\u003c\/strong\u003e The TRAC 69076 has a sand blasted, anodized gunmetal gray finish on its aircraft aluminum body.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much does the TRAC 69076 weigh?\u003c\/strong\u003e The TRAC 69076 Anchor Winch Mount Spacer\/Pedestal weighs 30 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the TRAC 69076 spacer\/pedestal removable from the winch?\u003c\/strong\u003e The catalog description for the TRAC 69076 does not describe it as separating from the winch for storage; that quick-release storage feature is described for the related TRAC 69075 mount instead.\u003c\/p\u003e","brand":"Trac Outdoor","offers":[{"title":"Default Title","offer_id":49028251582683,"sku":"TRC-69076","price":95.75,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/TRC-T10197__83471.1558351663.500.750.jpg?v=1785165642"},{"product_id":"trac-gen3-anchor-winch-mounting-plate-for-g3-fisherman-25-angler-30-pontoon-35-deckboat-40-winches","title":"Trac Gen3 Anchor Winch Mounting Plate for G3 Fisherman 25, Angler 30, Pontoon 35, Deckboat 40 Winches","description":"\u003cp\u003eThe Trac Gen3 Anchor Winch Mounting Plate (69071) is a dedicated installation base for Trac Gen3 anchor winches, giving boat owners a secure, purpose-built way to mount their winch to the bow or transom. The plate is machined from aircraft aluminum and finished with a sand blasted, anodized gunmetal gray coating for durability and a clean, corrosion-resistant appearance. It features 4 winch bolt holes for securing the winch itself, plus an extra hole that can be used for battery wire routing in some installations, keeping cabling tidy and protected. The plate is built with both an extended and a compact position for the anchor roller, allowing installers to adjust roller placement to suit the boat's bow configuration. Stainless steel mounting hardware is included, so no separate hardware purchase is needed for installation.\u003c\/p\u003e\u003cp\u003eThis mounting plate is designed specifically for the Trac Gen3 anchor winch lineup: the T10108-G3 Fisherman 25, T10208-G3 Angler 30, T10109-G3 Pontoon 35, and T10219-G3 Deckboat 40 anchor winches. It is not compatible with the T10108-25, T10109-35, T10208-AD, or T10219-AD winch models. It pairs with a range of Trac mounting accessories, including transom and side mounts, a quick-release plate, and a spacer-pedestal, giving installers flexibility in how and where the winch is mounted on the boat.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Trac\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e 69071\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct Type:\u003c\/strong\u003e Anchor Winch Mounting Plate\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatible Anchor Winch Models:\u003c\/strong\u003e T10108-G3 Fisherman 25, T10208-G3 Angler 30, T10109-G3 Pontoon 35, T10219-G3 Deckboat 40\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNot Compatible With:\u003c\/strong\u003e T10108-25, T10109-35, T10208-AD, T10219-AD\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWinch Bolt Holes:\u003c\/strong\u003e 4\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePlate Thickness:\u003c\/strong\u003e 0.4 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eModule Installation Holes (Forward Position):\u003c\/strong\u003e 8\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eModule Installation Holes (Rear Position):\u003c\/strong\u003e 8\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAnchor Roller Position:\u003c\/strong\u003e Extended and Compact\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Aircraft Aluminum\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFinish:\u003c\/strong\u003e Anodized Gunmetal Gray, Sand Blasted\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHardware Included:\u003c\/strong\u003e Stainless Steel\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatible Mounts\/Accessories:\u003c\/strong\u003e T10194 90 Degree Transom and Side Mount, T10195 12 Degree Transom and Side Mount, T10196 Quick-Release Plate, T10197 Spacer-Pedestal\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct Dimensions:\u003c\/strong\u003e 8 x 13 x 0.5 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 2.7 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 666996101932\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eT10108-G3 Fisherman 25 Anchor Winch\u003c\/li\u003e\n\u003cli\u003eT10208-G3 Angler 30 Anchor Winch\u003c\/li\u003e\n\u003cli\u003eT10109-G3 Pontoon 35 Anchor Winch\u003c\/li\u003e\n\u003cli\u003eT10219-G3 Deckboat 40 Anchor Winch\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat anchor winches fit the Trac Gen3 Anchor Winch Mounting Plate (69071)?\u003c\/strong\u003e The Trac 69071 mounting plate is built for the T10108-G3 Fisherman 25, T10208-G3 Angler 30, T10109-G3 Pontoon 35, and T10219-G3 Deckboat 40 Gen3 anchor winches.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes the 69071 mounting plate fit the T10108-25 or T10109-35 winches?\u003c\/strong\u003e No. The Trac Gen3 Anchor Winch Mounting Plate (69071) specifically does not fit the T10108-25, T10109-35, T10208-AD, or T10219-AD anchor winch models.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow thick is the Trac 69071 anchor winch mounting plate?\u003c\/strong\u003e The plate thickness on the Trac Gen3 Anchor Winch Mounting Plate is 0.4 inches.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat material is the Trac Gen3 mounting plate made from?\u003c\/strong\u003e It is machined from aircraft aluminum, giving the 69071 mounting plate strength while keeping weight down for marine installation.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat finish does the Trac 69071 mounting plate have?\u003c\/strong\u003e The mounting plate has a sand blasted surface with an anodized gunmetal gray finish for corrosion resistance and appearance.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes the Trac Gen3 Anchor Winch Mounting Plate come with hardware?\u003c\/strong\u003e Yes, stainless steel hardware is included with the 69071 mounting plate, so no separate hardware purchase is required for installation.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow many winch bolt holes does the 69071 mounting plate have?\u003c\/strong\u003e There are 4 winch bolt holes on the Trac Gen3 Anchor Winch Mounting Plate for securing the anchor winch.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan the extra hole on the Trac 69071 plate be used for wiring?\u003c\/strong\u003e Yes, the mounting plate includes an extra hole that can be used for battery wire routing in some installations.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat other Trac accessories work with the 69071 mounting plate?\u003c\/strong\u003e The Gen3 Anchor Winch Mounting Plate is compatible with the T10194 90 degree transom and side mount, T10195 12 degree transom and side mount, T10196 quick-release plate, and T10197 spacer-pedestal.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat are the dimensions and weight of the Trac 69071 mounting plate?\u003c\/strong\u003e The mounting plate measures 8 x 13 x 0.5 inches and weighs 2.7 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes the Trac Gen3 mounting plate support different anchor roller positions?\u003c\/strong\u003e Yes, the 69071 plate is designed with both an extended and a compact position for the anchor roller.\u003c\/p\u003e","brand":"Trac Outdoor","offers":[{"title":"Default Title","offer_id":49028251615451,"sku":"TRC-69071","price":103.07,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/Gen3-Mounting-Plate__76200.1558352638.500.750.jpg?v=1785165642"},{"product_id":"trac-t10192-winch-mounting-plate-for-anchor-winch-mount-spacer-pedestal-69076","title":"TRAC T10192 Winch Mounting Plate for Anchor Winch Mount Spacer\/Pedestal 69076","description":"\u003cp\u003eThe TRAC T10192 Mounting Plate is a winch mounting component built for anchor winch installations on boats and boat trailers. It is designed to pair with the TRAC 69076 Anchor Winch Mount Spacer\/Pedestal, a 1-inch riser that raises and supports the winch mount, giving installers a stable base for positioning an anchor winch away from the deck or trailer surface.\u003c\/p\u003e\u003cp\u003eThe T10192 is one of several mounting options in TRAC's anchor winch mounting system, which also includes the T10193 G3 Mounting Plate, the T10194 90-degree Transom and Side Mount, the T10195 12-degree Transom and Side Mount, and the T10196 Quick-Release Plate. Each of these is a separate part number built for a different mounting configuration, so the T10192 should be selected specifically when a standard flat mounting plate is needed rather than an angled transom mount or a quick-release setup.\u003c\/p\u003e\u003cp\u003eThe T10192 is categorized under Boat Trailer Winches and weighs 1.5 pounds, making it a lightweight addition to an anchor winch setup.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e TRAC\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e T10192\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct Category:\u003c\/strong\u003e Boat Trailer Winches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 1.5 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 666996101963\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCompatible Mounting Component:\u003c\/strong\u003e TRAC 69076 Anchor Winch Mount Spacer\/Pedestal (1-Inch Riser)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003cul\u003e\u003cli\u003eCompatible with the TRAC 69076 Anchor Winch Mount Spacer\/Pedestal (1-Inch Riser)\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eReplaces (OEM)\u003c\/h3\u003e\u003cul\u003e\u003cli\u003eNot applicable\u003c\/li\u003e\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat is the TRAC T10192 Mounting Plate used for?\u003c\/strong\u003e The T10192 is a mounting plate used to install an anchor winch, and it is built to work with the TRAC 69076 Anchor Winch Mount Spacer\/Pedestal, a 1-inch riser that raises the winch mounting point above the deck or trailer surface.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes the T10192 fit the TRAC 69076 Spacer\/Pedestal?\u003c\/strong\u003e Yes, the TRAC 69076 Anchor Winch Mount Spacer\/Pedestal is listed as compatible with the T10192 Mounting Plate as part of the same anchor winch mounting system.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the difference between the T10192 and the T10193 G3 Mounting Plate?\u003c\/strong\u003e Both are mounting plates in the TRAC anchor winch lineup, but they are separate part numbers: T10192 is the standard Mounting Plate, while T10193 is the G3 Mounting Plate, a distinct SKU for a different mounting application.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow is the T10192 different from the T10194 and T10195 transom mounts?\u003c\/strong\u003e The T10194 (90-degree Transom and Side Mount) and T10195 (12-degree Transom and Side Mount) are angled transom\/side mounting brackets, while the T10192 is a flat Mounting Plate, so the correct part number depends on the mounting angle and location needed.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the T10192 the same as the T10196 Quick-Release Plate?\u003c\/strong\u003e No, the T10196 Quick-Release Plate is a separate part number designed for quick-release mounting, while the T10192 is the standard fixed Mounting Plate in TRAC's anchor winch mounting system.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much does the TRAC T10192 Mounting Plate weigh?\u003c\/strong\u003e The TRAC T10192 Mounting Plate weighs 1.5 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat category does the T10192 fall under?\u003c\/strong\u003e The TRAC T10192 is categorized under Boat Trailer Winches.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the T10192 a genuine TRAC part?\u003c\/strong\u003e Yes, T10192 is TRAC's own public part number for this Mounting Plate, not a generic aftermarket substitute.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan the T10192 Mounting Plate be used without the 69076 Spacer\/Pedestal?\u003c\/strong\u003e The T10192 Mounting Plate is documented as compatible with the TRAC 69076 Anchor Winch Mount Spacer\/Pedestal, which functions as the 1-inch riser base for the mounting plate in TRAC's anchor winch mounting system.\u003c\/p\u003e","brand":"Trac Outdoor","offers":[{"title":"Default Title","offer_id":49028252860635,"sku":"TRC-T10192","price":53.28,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/2ndGenPlate__47844.1739462755.500.750.jpg?v=1785165652"},{"product_id":"maxwell-p103864-emergency-crank-handle-for-rc8-rc10-freedom-series-windlasses","title":"Maxwell P103864 Emergency Crank Handle for RC8, RC10 \u0026 Freedom Series Windlasses","description":"\u003cp\u003eThe Maxwell P103864 Emergency Crank Handle is a manual backup for RC8 and RC10 Series anchor winches and Freedom Series windlasses. When electrical power to the windlass is unavailable, this handle lets you raise or lower the anchor by hand, giving boaters a dependable way to manage ground tackle even in a power failure or other operational issue.\u003c\/p\u003e\u003cp\u003eThe handle is constructed of lightweight, durable injection-moulded plastic. Because of this construction, it floats if it is accidentally dropped overboard, reducing the chance of losing it over the side during an emergency retrieval. Two sizes are available to suit the constraints of most foredeck configurations, so boaters can choose the length that fits the deck layout and hardware clearance around their windlass installation.\u003c\/p\u003e\u003cp\u003eThis crank handle is designed for use specifically with RC8 and RC10 Series anchor winches and Freedom Series windlasses. Keep one aboard as a stowed emergency backup alongside your primary electric windlass controls.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Maxwell\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e P103864\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 9414761103855\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e Injection-moulded plastic\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eColor:\u003c\/strong\u003e Black\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 0.43 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eItem Dimensions:\u003c\/strong\u003e 10 x 5 x 5 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePackage Dimensions:\u003c\/strong\u003e 12 x 4 x 1 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBuoyancy:\u003c\/strong\u003e Floats if dropped overboard\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSizes Available:\u003c\/strong\u003e Two sizes to suit different foredeck configurations\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eMaxwell RC8 Series anchor winches\u003c\/li\u003e\n\u003cli\u003eMaxwell RC10 Series anchor winches\u003c\/li\u003e\n\u003cli\u003eMaxwell Freedom Series windlasses\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat is the Maxwell P103864 crank handle used for?\u003c\/strong\u003e It is an emergency backup for raising or lowering the anchor by hand on RC8 and RC10 Series anchor winches and Freedom Series windlasses when electrical power is unavailable.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhich windlasses does the P103864 handle fit?\u003c\/strong\u003e The P103864 is designed for use with Maxwell RC8 Series and RC10 Series anchor winches, as well as Freedom Series windlasses.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the P103864 handle made of?\u003c\/strong\u003e It is made of lightweight, durable injection-moulded plastic.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWill the crank handle sink if I drop it overboard?\u003c\/strong\u003e No. Because the P103864 is made of injection-moulded plastic, it floats if it is accidentally dropped overboard.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes this handle come in more than one size?\u003c\/strong\u003e Yes, two sizes of the P103864 are available to suit the constraints of most foredeck configurations.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much does the P103864 crank handle weigh?\u003c\/strong\u003e The Maxwell P103864 weighs 0.43 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat are the dimensions of the P103864 handle?\u003c\/strong\u003e Item dimensions are 10 x 5 x 5 inches, with package dimensions of 12 x 4 x 1 inches.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat color is the P103864 crank handle?\u003c\/strong\u003e The P103864 is black.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the P103864 a genuine Maxwell part?\u003c\/strong\u003e Yes, P103864 is the genuine Maxwell manufacturer part number for this emergency crank handle.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is included when I order the P103864?\u003c\/strong\u003e One P103864 Emergency Crank Handle for RC and Freedom Series windlasses is included.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan I use this handle for routine anchor operation, not just emergencies?\u003c\/strong\u003e The P103864 is designed as a manual emergency backup for RC8, RC10, and Freedom Series windlasses when power is unavailable, rather than for routine operation.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy should I choose the correct size of the P103864 handle?\u003c\/strong\u003e Maxwell offers two sizes of the P103864 to suit different foredeck configurations, so selecting the right size ensures proper clearance around your windlass installation.\u003c\/p\u003e","brand":"Vetus","offers":[{"title":"Default Title","offer_id":49028255187163,"sku":"MAX-P103864","price":70.74,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/Untitled-1__54773.1755896057.500.750.jpg?v=1785165715"},{"product_id":"lewmar-swa-shallow-water-anchor-motor-mounting-bracket-available-in-black-and-white","title":"Lewmar SWA Shallow Water Anchor Motor Mounting Bracket - Available in Black and White","description":"\u003cp\u003eThe Lewmar SWA Motor Mounting Bracket is the dedicated mounting component for the Lewmar SWA shallow water anchor system, securing the anchor's drive motor firmly to the pole for reliable, vibration-free operation. Machined and finished for long-term exposure to sun, salt, and spray, this bracket is the correct replacement or spare part when the original mount is damaged, corroded, or worn from repeated deployments. Choose the finish that matches your existing SWA hardware and boat color scheme.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eBrand: Lewmar\u003c\/li\u003e\n\u003cli\u003eProduct Line: SWA Motor Mounting Bracket\u003c\/li\u003e\n\u003cli\u003eCompatible System: Lewmar SWA Shallow Water Anchor\u003c\/li\u003e\n\u003cli\u003eAvailable Finishes: Black, White\u003c\/li\u003e\n\u003cli\u003eGenuine OEM Lewmar replacement part\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSizes \u0026amp; Options\u003c\/h3\u003e\u003cp\u003eThis bracket is available in two color finishes, Black and White, so you can match your existing Lewmar SWA pole and hardware or coordinate with your boat's color scheme. Both finishes are functionally identical and interchangeable; select based on appearance only. Confirm the color of your current SWA bracket before ordering to keep the mounting hardware visually consistent.\u003c\/p\u003e","brand":"Lewmar","offers":[{"title":"Black","offer_id":49046166667483,"sku":"LEW-2024028464","price":143.01,"currency_code":"USD","in_stock":false},{"title":"White","offer_id":49046166700251,"sku":"LEW-2024028467","price":143.01,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/i_cbf714f0-f77e-4115-b01b-91269eeda871.png?v=1785395486"},{"product_id":"maxwell-covered-windlass-foot-switch-deck-mount-foot-control-12v-200a","title":"Maxwell Covered Windlass Foot Switch - Deck-Mount Foot Control, 12V 200A","description":"\u003cp\u003eThe Maxwell Covered Windlass Foot Switch is the deck-mounted control that lets you run your Maxwell anchor windlass hands-free while you manage the rode and anchor. Rated for 12 Volt, 200 Amp service, this foot-operated switch closes the circuit to power the windlass motor up or down without requiring you to reach for a helm or remote control switch. A hinged or fitted cover shields the actuator button from spray, dropped gear, and accidental foot traffic on deck, extending the life of the switch in a wet, high-traffic environment. Constructed of durable plastic housing designed for marine deck mounting, it is a direct-fit replacement or new install for boats using Maxwell windlass systems. Available in Black or White to match your deck hardware and non-skid color scheme.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eBrand: Maxwell\u003c\/li\u003e\n\u003cli\u003eProduct Type: Foot Switch (Covered)\u003c\/li\u003e\n\u003cli\u003eElectrical Rating: 12 Volt, 200 Amp\u003c\/li\u003e\n\u003cli\u003eMaterial: Plastic\u003c\/li\u003e\n\u003cli\u003eItem Dimensions (L x W x H): 9 x 7 x 3 inches\u003c\/li\u003e\n\u003cli\u003eWeight: approx. 0.48 lbs\u003c\/li\u003e\n\u003cli\u003eQuantity: 1 per pack\u003c\/li\u003e\n\u003cli\u003eColors: Black, White\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSizes \u0026amp; Options\u003c\/h3\u003e\u003cp\u003eThis foot switch is offered in two color options, Black (P19006) and White (P19007), so you can match it to your deck layout or existing Maxwell hardware. Both versions share identical 12V\/200A electrical ratings, dimensions, and the same protective hinged cover -- the only difference is color. Choose the finish that best coordinates with your boat's deck fittings and non-skid surface.\u003c\/p\u003e","brand":"Maxwell Windlass","offers":[{"title":"Black","offer_id":49048117805275,"sku":"MAX-P19006","price":77.25,"currency_code":"USD","in_stock":true},{"title":"White","offer_id":49048117838043,"sku":"MAX-P19007","price":77.25,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/61_akWWiq5L_cefd6bc1-e7e3-4146-b8b3-4670e304429d.jpg?v=1785434106"},{"product_id":"maxwell-breaker-isolator-panel-for-12v-24v-dc-windlass-systems-available-in-80-amp-and-135-amp","title":"Maxwell Breaker\/Isolator Panel for 12V\/24V DC Windlass Systems - Available in 80 Amp and 135 Amp","description":"\u003cp\u003eThe Maxwell Breaker\/Isolator Panel protects the main DC conductor circuit feeding your Maxwell windlass or capstan. Wired into the power supply line between the battery and the windlass motor, it guards against short circuits and reduces the risk of DC motor burn-out if the winch is overloaded or jams under load. The panel also functions as a manual isolator, letting you disconnect the battery or electrical supply whenever the windlass is not in use, which protects the system from accidental activation and stray current draw. Built for both 12V and 24V DC installations, this panel mounts close to the battery power source for the shortest possible run of unprotected cable. Choose the 80 Amp panel for lighter-duty windlass and capstan installations, or step up to the 135 Amp panel for higher-draw systems that need additional headroom.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eBrand: Maxwell\u003c\/li\u003e\n\u003cli\u003eCircuit Breaker Type: Standard\u003c\/li\u003e\n\u003cli\u003eMounting Type: Panel mount\u003c\/li\u003e\n\u003cli\u003eNumber of Poles: 2\u003c\/li\u003e\n\u003cli\u003eVoltage: 12V or 24V DC\u003c\/li\u003e\n\u003cli\u003eCategory: Switches and solenoids\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSizes \u0026amp; Options\u003c\/h3\u003e\u003cp\u003eThis panel is available in two current ratings: 80 Amp (P100790) and 135 Amp (P100791). Match the panel rating to your windlass motor's maximum draw and your existing wiring gauge -- check your windlass manufacturer's specification sheet for the recommended breaker size, and when in doubt, size up rather than down to avoid nuisance tripping under heavy load.\u003c\/p\u003e","brand":"Maxwell Windlass","offers":[{"title":"80 Amp Breaker\/Isolator Panel P100790","offer_id":49049054576859,"sku":"MAX-P100790","price":139.98,"currency_code":"USD","in_stock":false},{"title":"135 Amp Breaker\/Isolator Panel P100791","offer_id":49049054609627,"sku":"MAX-P100791","price":144.12,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/Untitled-1__96740.1763741580.500.750_4083cfac-506f-4fd3-8b31-1bfc19177e09.jpg?v=1785450479"},{"product_id":"anchorlift-anchor-turner-kit-automatic-anchor-alignment-for-1-4-to-1-2-chain","title":"Anchorlift Anchor Turner Kit - Automatic Anchor Alignment for 1\/4\" to 1\/2\" Chain","description":"\u003cp\u003eThe Anchorlift Anchor Turner Kit takes the guesswork out of anchor retrieval. As the windlass hauls in the chain, the turner automatically rotates the anchor so it parks correctly in the bow roller every time, eliminating the frustrating dance of jogging the windlass or reaching overboard to twist a crooked anchor into place. Built from high polish 316L stainless steel, each kit is matched to a specific chain size and anchor weight so the turner spins freely under load without binding or wearing prematurely. Whether you are running a compact bow roller on a weekend cruiser or a heavy-duty setup on a larger offshore boat, there is a size in this line rated for the chain and ground tackle you already carry.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eBrand: Anchorlift\u003c\/li\u003e\n\u003cli\u003eMaterial: High Polish 316L Stainless Steel\u003c\/li\u003e\n\u003cli\u003eChain sizes: 1\/4 inch, 3\/8 inch, 1\/2 inch\u003c\/li\u003e\n\u003cli\u003eAnchor capacity: up to 22 lbs, 110 lbs, or 175 lbs (80 kg) depending on size\u003c\/li\u003e\n\u003cli\u003eIncludes anchor connector swivel and anchor turner\u003c\/li\u003e\n\u003cli\u003eCorrosion-resistant for saltwater use\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSizes \u0026amp; Options\u003c\/h3\u003e\u003cp\u003eSelect the kit that matches your anchor chain diameter, not your anchor's brand or shape. Measure the chain link wire diameter (not the link length) and confirm your anchor's weight falls within the kit's rated capacity. Undersizing the turner for a heavier anchor can strain the swivel and turner; oversizing for lighter chain can leave the fit loose. If your chain size falls between two listed sizes, choose the next size up for a secure, low-play fit.\u003c\/p\u003e","brand":"Anchorlift","offers":[{"title":"1\/4\" Chain - Anchors to 22 lbs","offer_id":49049165693147,"sku":"ACL-965008","price":233.67,"currency_code":"USD","in_stock":true},{"title":"3\/8\" Chain - Anchors to 110 lbs","offer_id":49049165725915,"sku":"ACL-965011","price":511.45,"currency_code":"USD","in_stock":false},{"title":"1\/2\" Chain - Anchors to 175 lbs","offer_id":49049165758683,"sku":"ACL-965012","price":616.02,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/31YWBrSGZpL_2262cbd2-2f60-4833-893a-9ef9e5e2bacc.jpg?v=1785452871"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/collections\/Untitled-1__54773.1755896057.500.750.jpg?v=1785356940","url":"https:\/\/www.goodvibesmarina.com\/collections\/gvcat-anchoring-mooring-windlasses-anchor-winches-windlass-parts-switches-solenoids.oembed?page=2","provider":"Good Vibes Marina","version":"1.0","type":"link"}