{"product_id":"bennett-bolt912ed-electric-trim-tab-kit-9-x-12-edge-mount-part-6bt500135400","title":"Bennett BOLT912ED Electric Trim Tab Kit, 9 x 12 Edge Mount, Part 6BT500135400","description":"\u003cp\u003eThe Bennett BOLT912ED is a 9 inch by 12 inch electric trim tab kit built around an edge mount design for boats with limited vertical transom space. Trim tab sizing follows Bennett's span by chord format, meaning the tabs measure 9 inches side to side (span) and 12 inches fore to aft (chord). The edge mount configuration uses an adjustable upper hinge that requires only 6.39 inches of vertical transom clearance to install, and the tabs themselves turn up for added strength with piano-hinged backing plates. This kit is intended for trailered boats between 17 and 28 feet, and it is designed for single-actuator use per tab since two electric actuators cannot be synchronized on the same trim tab.\u003c\/p\u003e\u003cp\u003eEach kit includes two BEA2000 12-volt actuators housed in a water-tight black nylon casing. Wiring is concealed and protected as it runs through the upper hinge, leaving no exposed wires in the marine environment, and the main seal is mounted high on the actuator to guard against marine growth and water intrusion. The actuators produce up to 750 pounds of actuation and return force, drawing 10 amps at 250 pounds of load and up to 30 amps at full rated force, and connect through Deutsch DT Series 13 amp waterproof connectors. The kit ships with stainless steel trim planes and mounting plates, two 20 foot main harnesses, and 6 foot actuator harnesses, all with waterproof connectors. A control switch is not included and must be purchased separately. The kit is backed by a 5 year manufacturer's warranty.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e Bennett\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e 6BT500135400\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStyle:\u003c\/strong\u003e Electric Trim Tabs\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e Trim Tab Kit\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTrim Tab Size (Span x Chord):\u003c\/strong\u003e 9 inches x 12 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting Style:\u003c\/strong\u003e Edge Mount\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVertical Transom Space Required:\u003c\/strong\u003e 6.39 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eActuator Model:\u003c\/strong\u003e BEA2000\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eActuator Voltage:\u003c\/strong\u003e 12 volts\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eActuator Length:\u003c\/strong\u003e 13.25 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eActuator Stroke:\u003c\/strong\u003e 2.5 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWorking Force (Actuation and Return):\u003c\/strong\u003e 750 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCurrent Draw:\u003c\/strong\u003e 10 amps at 250 pounds, 30 amps at 750 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eElectrical Connector:\u003c\/strong\u003e Deutsch DT Series, 13 amp\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWire Harness Length:\u003c\/strong\u003e 20 feet main harness with 6 foot actuator harness, waterproof connectors\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTrim Plane Material:\u003c\/strong\u003e Stainless steel\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eActuator Housing Material:\u003c\/strong\u003e Black nylon\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWater Resistance:\u003c\/strong\u003e Water resistant, water-tight actuator seal\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSwitch:\u003c\/strong\u003e Sold separately\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWarranty:\u003c\/strong\u003e 5 year manufacturer's warranty\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 23 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 666285600306\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eYamaha Part Number:\u003c\/strong\u003e 6BT-50013-54-00\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eTrailered boats 17 to 28 feet in length\u003c\/li\u003e\n\u003cli\u003eSingle-actuator installations (two electric actuators cannot be synchronized on one tab)\u003c\/li\u003e\n\u003cli\u003eTransoms with limited vertical space (requires 6.39 inches of vertical clearance)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat size are the trim tabs in the Bennett BOLT912ED kit, part number 6BT500135400?\u003c\/strong\u003e The trim tabs measure 9 inches by 12 inches, sized as span (side to side) by chord (fore to aft). This edge mount kit, Bennett part 6BT500135400, uses the BOLT912ED design.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat boats is the Bennett BOLT912ED 9 x 12 trim tab kit designed for?\u003c\/strong\u003e This kit is designed for trailered boats between 17 and 28 feet in length, and it is intended for single-actuator installations since two electric actuators cannot be synchronized on the same tab.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much vertical transom space does this trim tab kit need?\u003c\/strong\u003e The Bennett BOLT912ED edge mount kit requires 6.39 inches of vertical transom space, under the 6.5 inch clearance needed for standard installations, making it suited to transoms with limited vertical room.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is included in the box with part number 6BT500135400?\u003c\/strong\u003e The kit ships with two BEA2000 12-volt trim tab actuators, two stainless steel trim planes with mounting plates, two 20 foot harnesses with waterproof connectors, and 6 foot actuator wire harnesses with waterproof connectors.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes the Bennett BOLT912ED kit include a control switch?\u003c\/strong\u003e No, a control switch is sold separately from the Bennett BOLT912ED trim tab kit; only the actuators, trim planes, and harnesses are included.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat material are the trim planes made of?\u003c\/strong\u003e The trim planes (tabs) in the Bennett BOLT912ED kit are stainless steel, paired with mounting plates and piano-hinged backing plates on the tab itself.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat voltage and electrical connectors does the BOLT912ED actuator use?\u003c\/strong\u003e Each BEA2000 actuator in this kit runs on 12 volts and terminates in a Deutsch DT Series 13 amp waterproof connector.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow is the Edge Mount design different from a standard mount trim tab kit?\u003c\/strong\u003e The Edge Mount design used on part 6BT500135400 has an adjustable upper hinge built for transoms with limited vertical space, and the tabs turn up for added strength with piano-hinged backing plates, features not found on a standard mount.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much force do the BOLT912ED actuators produce?\u003c\/strong\u003e The actuators are rated for 750 pounds of actuation and return force, drawing 10 amps at 250 pounds of load and up to 30 amps at the full 750 pound rating.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs this trim tab kit waterproof?\u003c\/strong\u003e Yes, the Bennett BOLT912ED actuator uses a water-tight black nylon housing with the main seal positioned high on the unit to resist marine growth and water intrusion, and all harness connectors are waterproof.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat warranty comes with the Bennett BOLT912ED trim tab kit?\u003c\/strong\u003e Bennett covers this kit, part 6BT500135400, with a 5 year manufacturer's warranty.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan I upgrade from a Lenco trim tab system to this Bennett kit?\u003c\/strong\u003e Bennett offers a separate Lenco-to-BOLT conversion kit that lets boaters replace Lenco actuators with Bennett BOLT actuators using existing mounting holes, though that conversion kit is a different product from the BOLT912ED 9 x 12 edge mount kit itself.\u003c\/p\u003e","brand":"Bennett Marine","offers":[{"title":"Default Title","offer_id":49027450929371,"sku":"BEN-BOLT912ED","price":643.11,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/Bennett-BOLT912ED-9-inch-by-12-inch-BOLT-Electric-Trim-Tab-Kit-Edge-Mount__76780.1739477219.500.750.jpg?v=1785163395","url":"https:\/\/www.goodvibesmarina.com\/products\/bennett-bolt912ed-electric-trim-tab-kit-9-x-12-edge-mount-part-6bt500135400","provider":"Good Vibes Marina","version":"1.0","type":"link"}