{"product_id":"t-h-marine-cmc-pt-130-electric-hydraulic-tilt-and-trim-for-outboard-motors-up-to-130-hp","title":"T-H Marine CMC PT-130 Electric Hydraulic Tilt and Trim for Outboard Motors up to 130 HP","description":"\u003cp\u003eThe T-H Marine CMC PT-130 is an electric hydraulic tilt and trim unit built for outboard motors up to 130 HP. It is constructed from 1\/2 inch 6061 T6 extruded aluminum with stainless steel hardware for corrosion resistance in marine environments, and it mounts using the standard B.I.A. Bolt hole pattern with the included hardware for a straightforward installation. The PT-130 provides a 6 inch set back, which lets the outboard sit further from the transom and be mounted higher than a transom-mounted motor, while delivering 20 degrees of trim and 90 degrees of tilt. The electric hydraulic actuator is rated at 7853 pounds of thrust. Each unit ships complete with the hydraulic PT-130 unit, a wire assembly, an up-down toggle switch, and stainless steel mounting hardware. For boats and motors that are not pre-drilled to the B.I.A. Pattern, some drilling may be required, and installation involves supporting the motor with a properly rated lifting device, removing the motor's existing transom mounting nuts, mounting the PT-130 to the transom with clearance for full tilt, and reattaching the motor using the original nuts with flat and lock washers. Motors with transom clamps that tighten inside the splash well require a separate T-H Marine CMC transom clamp adapter (sold separately) to fit the PT-130.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e T-H Marine CMC\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e 13002\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower Rating:\u003c\/strong\u003e Up to 130 HP\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSet Back:\u003c\/strong\u003e 6 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTrim Angle:\u003c\/strong\u003e 20 degrees\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTilt Angle:\u003c\/strong\u003e 90 degrees\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eActuator Type:\u003c\/strong\u003e Electric hydraulic\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThrust Rating:\u003c\/strong\u003e 7853 pounds of thrust\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e 1\/2 inch 6061 T6 extruded aluminum\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHardware:\u003c\/strong\u003e Stainless steel\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBolt Hole Pattern:\u003c\/strong\u003e Standard B.I.A.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 43 pounds\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePackage Dimensions:\u003c\/strong\u003e 19.5 x 14.5 x 6.5 inches\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUPC:\u003c\/strong\u003e 130021300200\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIncludes:\u003c\/strong\u003e Hydraulic PT-130 unit, wire assembly, up-down toggle switch, stainless steel mounting hardware\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003cp\u003eDesigned for outboard motors up to 130 HP with the standard B.I.A. Outboard mounting hole configuration. Motors with transom clamps that tighten inside the splash well require the separate T-H Marine CMC transom clamp adapter to mount to the PT-130.\u003c\/p\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat horsepower range does the CMC PT-130 support?\u003c\/strong\u003e The T-H Marine CMC PT-130 is designed for outboard motors up to 130 HP and smaller.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much set back does the PT-130 provide?\u003c\/strong\u003e It provides a 6 inch set back, positioning the outboard further from the transom so it can be mounted higher than a transom-mounted motor.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the tilt and trim range on the PT-130?\u003c\/strong\u003e The unit offers 20 degrees of trim and 90 degrees of tilt.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the thrust rating of the PT-130's actuator?\u003c\/strong\u003e The electric hydraulic actuator on part number 13002 is rated at 7853 pounds of thrust.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the PT-130 made of?\u003c\/strong\u003e The PT-130 is constructed from 1\/2 inch 6061 T6 extruded aluminum with stainless steel hardware for corrosion resistance in marine environments.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes the PT-130 fit standard outboard motor mounting holes?\u003c\/strong\u003e Yes, it is predrilled to fit the standard B.I.A. Outboard motor mounting hole configuration; if your boat and motor are not pre-drilled, some drilling may be required.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat comes included with the CMC PT-130?\u003c\/strong\u003e Each PT-130 unit ships with the hydraulic PT-130 unit itself, a wire assembly, an up-down toggle switch, and stainless steel mounting hardware.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWill the PT-130 work with an outboard that has transom clamps?\u003c\/strong\u003e Motors with clamps that tighten inside the splash well need the separate T-H Marine CMC transom clamp adapter to fit the PT-130; it is not included with part number 13002.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow is the PT-130 installed?\u003c\/strong\u003e Installation involves supporting the motor with a properly rated lifting device, removing the four nuts mounting the motor to the transom, mounting the PT-130 to the transom with clearance for full tilt, and reattaching the motor using the original nuts along with flat and lock washers.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much does the CMC PT-130 weigh?\u003c\/strong\u003e The T-H Marine CMC PT-130 (part number 13002) weighs 43 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat are the package dimensions of the PT-130?\u003c\/strong\u003e The PT-130 ships in a package measuring 19.5 x 14.5 x 6.5 inches.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the PT-130 an electric or manual tilt and trim unit?\u003c\/strong\u003e It is an electric hydraulic tilt and trim unit, operated with the included up-down toggle switch.\u003c\/p\u003e","brand":"CMC Marine","offers":[{"title":"Default Title","offer_id":49027442802907,"sku":"T-H-13002","price":1121.38,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/T-H-Marine-CMC-PT-130-Electric-Hydraulic-Tilt-and-Trim__83832.1739459056.500.750.jpg?v=1785163481","url":"https:\/\/www.goodvibesmarina.com\/products\/t-h-marine-cmc-pt-130-electric-hydraulic-tilt-and-trim-for-outboard-motors-up-to-130-hp","provider":"Good Vibes Marina","version":"1.0","type":"link"}