{"product_id":"t-h-marine-ell-3-4-90-degree-barbed-elbow-fitting-for-3-4-inch-id-marine-hose","title":"T-H Marine ELL-3\/4 Barbed Elbow Fitting, 90 Degree, 3\/4 Inch Hose ID","description":"\u003cp\u003eThe T-H Marine ELL-3\/4 is a 90 degree barbed elbow fitting molded specifically to fit marine hose dimensions for a 3\/4 inch ID hose. Instead of bending hose sharply around a tight turn and risking a kink that restricts flow, this elbow lets the hose route through a clean 90 degree change in direction while keeping the barb securely seated. It is also commonly used as a hose junction fitting when repairing a damaged section of hose, letting you cut out the bad section and rejoin the two ends. Both legs of the fitting share the same barb dimension, so hose slides on and grips evenly on either side of the turn. This makes it a straightforward, reliable component for livewell plumbing, bilge and washdown hose runs, aerator lines, or any onboard plumbing where a 3\/4 inch ID hose needs to change direction or be spliced without adding a rigid, kink-prone bend. Installation is simple: work the 3\/4 inch hose ends over each barbed leg and secure with standard hose clamps.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrand:\u003c\/strong\u003e T-H Marine\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer Part Number:\u003c\/strong\u003e ELL-3\/4\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProduct Name:\u003c\/strong\u003e Barbed Elbow Fitting\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitting Angle:\u003c\/strong\u003e 90 degrees\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHose Inside Diameter:\u003c\/strong\u003e 3\/4 inch\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBarb Configuration:\u003c\/strong\u003e Equal barb dimension on both legs\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUse:\u003c\/strong\u003e Hose routing turn or hose junction\/repair splice\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 1 pounds\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eFitment\u003c\/h3\u003e\u003cp\u003eFits any marine plumbing system using 3\/4 inch ID hose.\u003c\/p\u003e\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eWhat hose size does the T-H Marine ELL-3\/4 fit?\u003c\/strong\u003e The ELL-3\/4 is sized for 3\/4 inch ID (inside diameter) hose and is molded specifically to marine hose dimensions for a secure fit.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eCan this elbow be used to repair a damaged hose?\u003c\/strong\u003e Yes, the ELL-3\/4 barbed elbow can be used as a hose junction fitting to splice two ends of 3\/4 inch ID hose together when repairing a damaged section.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhy use a 90 degree elbow instead of just bending the hose?\u003c\/strong\u003e Bending 3\/4 inch ID hose sharply around a tight turn can kink it and restrict water flow; the ELL-3\/4 elbow provides a molded 90 degree turn so the hose routes cleanly without kinking.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eIs the barb size the same on both ends of the ELL-3\/4?\u003c\/strong\u003e Yes, both legs of the T-H Marine ELL-3\/4 elbow have the same barb dimension, so hose grips evenly regardless of which leg it is fitted to.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat is the ELL-3\/4 made for, livewells or bilge lines?\u003c\/strong\u003e The ELL-3\/4 barbed elbow works for any 3\/4 inch ID hose run onboard, including livewell plumbing, aerator lines, bilge, and washdown hose systems.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eHow much does the ELL-3\/4 weigh?\u003c\/strong\u003e The T-H Marine ELL-3\/4 barbed elbow fitting weighs 1 pounds.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDo I need clamps to install this fitting?\u003c\/strong\u003e Standard hose clamps are used to secure the 3\/4 inch ID hose ends onto each barbed leg of the ELL-3\/4 elbow after the hose is worked onto the barb.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eDoes T-H Marine make this elbow in other hose sizes?\u003c\/strong\u003e T-H Marine's barbed elbow fitting line also includes sizes for 1\/4 inch, 3\/8 inch, 1-1\/8 inch, and 1-1\/2 inch ID hose; the ELL-3\/4 is the 3\/4 inch ID version.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWhat material is the ELL-3\/4 elbow made from?\u003c\/strong\u003e The ELL-3\/4 is a molded fitting built to marine hose dimensions; specific material composition is not specified.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eWill the ELL-3\/4 fit both push-on and threaded hose systems?\u003c\/strong\u003e The ELL-3\/4 is a barbed fitting, designed for push-on 3\/4 inch ID hose secured with a hose clamp, not a threaded connection.\u003c\/p\u003e","brand":"T-H Marine","offers":[{"title":"Default Title","offer_id":48991262572763,"sku":"T-H-ELL-3-4DP","price":8.95,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0839\/7586\/4539\/files\/3-4-ell-3-4-dp-barbed-elbow-fittings-28282898022443_4ea790ed-555e-4cd3-9ce4-20b55b195886.jpg?v=1784498505","url":"https:\/\/www.goodvibesmarina.com\/products\/t-h-marine-ell-3-4-90-degree-barbed-elbow-fitting-for-3-4-inch-id-marine-hose","provider":"Good Vibes Marina","version":"1.0","type":"link"}