Bob's Machine Action Series Hydraulic Tilt and Trim 100-701100-NOPC for Clamp-On Motors up to 30 HP

The Bob's Machine Action Series Hydraulic Tilt and Trim is an all-in-one tilt and trim unit built for clamp-on outboard motors up to 30 HP. Designed to simplify rigging and improve on-water performance, this unit lets skippers trim the boat for a smoother, drier ride while making it easy to raise and lower the motor at the launch ramp. When fully trimmed in, the unit provides a negative 3-degree tuck-under angle that helps the boat get on plane faster from a standing start. Once on plane, the boat's running angle can be fine-tuned by trimming the unit up to its maximum of 75 degrees for the best balance of speed and handling.

Installation is straightforward since the tilt and trim arrives complete with a trim plate, wiring harness, relays, and a rocker style control switch, so there is no need to source separate components. The unit carries a 5-1/2 inch standard setback and has overall mounting dimensions of 10 inches wide by 11.5 inches long. Bob's Machine backs the Action Series Tilt and Trim with a limited lifetime structural warranty, reflecting its build quality for repeated use on clamp-on motor applications.

Specifications

• Brand: Bob's Machine
• Manufacturer Part Number: 100-701100-NOPC
• Product Type: Hydraulic Tilt and Trim
• Motor Compatibility: Clamp-on motors up to 30 HP
• Maximum Tilt Angle: 75 degrees
• Trim Angle (fully trimmed in): Negative 3 degree tuck-under angle
• Standard Setback: 5-1/2 inches
• Overall Mounting Dimensions: 10 inches width x 11.5 inches length
• Weight: 35 pounds
• Warranty: Limited lifetime structural warranty
• Included Components: Trim plate, wiring harness, relays, rocker style control switch
• UPC: 894721000872

Fitment

• Clamp-on outboard motors up to 30 HP

Frequently Asked Questions

What is the maximum horsepower rating for the Bob's Machine Action Series Tilt and Trim? The Bob's Machine Action Series Tilt and Trim, part number 100-701100-NOPC, is designed for clamp-on motors up to 30 HP.

Does this tilt and trim work with clamp-on outboard motors only? Yes, the 100-701100-NOPC tilt and trim is designed specifically for clamp-on motors and is not intended for other mounting styles.

What is the maximum tilt angle on this unit? It trims up to a maximum of 75 degrees, allowing the boat's running angle to be optimized after reaching plane.

What happens when the tilt and trim is fully trimmed in? When fully trimmed in, the Action Series Tilt and Trim provides a negative 3-degree tuck-under angle for faster starts and quicker time to plane.

How much setback does this tilt and trim have? The Bob's Machine Action Series Tilt and Trim has a 5-1/2 inch standard setback.

What are the overall mounting dimensions of this unit? The overall mounting dimensions of the 100-701100-NOPC tilt and trim are 10 inches wide by 11.5 inches long.

How much does the Bob's Machine Action Series Tilt and Trim weigh? This tilt and trim weighs 35 pounds.

What is included with this tilt and trim unit? The 100-701100-NOPC ships complete with a trim plate, wiring harness, relays, and a rocker style control switch.

Is a separate hydraulic pump required to run this unit? No, the Action Series Tilt and Trim is an all-in-one unit, so no separate pump needs to be mounted or plumbed inside the boat.

How difficult is it to install this tilt and trim? Installation is straightforward since the 100-701100-NOPC arrives as a complete all-in-one unit with the wiring harness, relays, and switch already included, requiring only connection of power and switch wiring.

What warranty comes with the Bob's Machine Action Series Tilt and Trim? This unit carries a limited lifetime structural warranty from Bob's Machine.

Can this tilt and trim adjust the boat's ride while underway? Yes, the 100-701100-NOPC allows skippers to trim the boat for a smoother, drier ride, in addition to raising and lowering the motor at the launch ramp.