SeaStar CC17010 400 Series Control Cable, 10 Feet, for Pre-1979 OMC/Johnson/Evinrude with BRP/OMC Controls

The SeaStar CC17010 is a 400 Series standard-type control cable engineered as a direct, OEM-style replacement for pre-1979 OMC, Johnson, and Evinrude outboard engines equipped with BRP/OMC control heads. Measuring 10 feet in length, it uses the existing connection components at the control head, so installation follows the same routing and attachment points as the original cable it replaces.

Construction features stainless steel terminals and conduit fittings paired with stainless or nylon-covered core wires and moisture protective seals, giving the cable added resistance to corrosion at the connection points. The core wire runs inside a long-wearing HDPE liner that is ultra smooth and lubricated for life, supporting an 8-inch minimum bend radius during installation. The black HDPE outer jacket resists abrasion and withstands UV exposure, salt water, chemicals, gasoline, and oil, making it suited to the marine environment.

Each cable is environmentally tested for marine applications and is built to exceed the engine manufacturer's specifications. It is made in the U.S.A. And is lifetime lubricated at the factory. Before ordering, verify that 10 feet is the correct cable length for your specific control run.

Specifications

• Brand: SeaStar
• Manufacturer Part Number: CC17010
• Product Line: 400 Series
• Type: Standard
• Length: 10 feet
• Weight: 1.27 pounds
• Outer Jacket Material: HDPE
• Outer Jacket Color: Black
• Terminals: Stainless steel
• Core Wire: Stainless or nylon-covered
• Minimum Bend Radius: 8 inches
• Compatible Controls: BRP/OMC controls
• Country of Origin: Made in the U.S.A.
• UPC: 731957020888

Fitment

• Pre-1979 OMC/Johnson/Evinrude outboard engines with BRP/OMC controls

Frequently Asked Questions

What engines does the SeaStar CC17010 control cable fit? The CC17010 is designed for pre-1979 OMC, Johnson, and Evinrude outboard engines equipped with BRP/OMC control heads.

How long is this control cable? The SeaStar CC17010 is 10 feet in length, part of the 400 Series standard cable line.

Will this cable connect to my existing control head without modification? Yes, the CC17010 is a drop-in replacement engineered to use the existing connection components on pre-1979 OMC/Johnson/Evinrude control heads with BRP/OMC controls.

What is the outer jacket made of? The CC17010 has a black HDPE outer jacket that resists abrasion and withstands UV exposure, salt water, chemicals, gasoline, and oil.

What material are the terminals and core wire? Stainless steel terminals and conduit fittings are used along with stainless or nylon-covered core wires and moisture protective seals for corrosion resistance.

Does the SeaStar CC17010 come pre-lubricated? Yes, this cable is lifetime lubricated at the factory, and the HDPE liner is ultra smooth for reduced friction over the life of the cable.

How much does the CC17010 weigh? The SeaStar CC17010 control cable weighs 1.27 pounds.

What is the minimum bend radius for installation? The CC17010 has an 8-inch minimum bend radius, which should be respected when routing the cable during installation.

Is this cable made to a higher standard than the original equipment cable? The CC17010 is built to exceed the engine manufacturer's specifications and is environmentally tested for marine applications.

Where is the SeaStar CC17010 manufactured? This control cable is made in the U.S.A.

How do I know if 10 feet is the right length for my boat? Measure your existing control cable run before ordering the CC17010, since control cables must match the application length for proper operation; the 10-foot length will not work if a different length is required.

Does the CC17010 replace both throttle and shift cables? The CC17010 is a single 400 Series control cable assembly for use with BRP/OMC control heads on pre-1979 OMC/Johnson/Evinrude engines; check your control head setup to confirm the correct cable for throttle or shift function.