T-H Marine CMC PT-35 Electric Hydraulic Tilt and Trim for Outboards up to 35 HP, Part 52100

The T-H Marine CMC PT-35 is an electric hydraulic tilt and trim system built for outboards up to 35 HP, giving small and lightweight boats the kind of trim control normally found only on larger, factory-equipped outboards. It is designed for jon boats, aluminum fishing boats, inflatables, tiller-steer outboards, and other small skiffs and utility boats where precise motor angle adjustment improves handling and performance.

By adjusting motor angle on the fly, the PT-35 helps boats get on plane faster even with heavier loads, improves top-end speed and fuel efficiency, reduces bow rise and porpoising, and allows the operator to quickly tilt the motor up for running in shallow water or protecting the lower unit near hazards or while trailering. The unit uses a fully self-contained electric hydraulic actuator rated at 7853 lbs of thrust, so no external pumps or hydraulic hoses are required for installation.

Construction is high-strength aluminum with corrosion-resistant components suited for both freshwater and saltwater environments. The PT-35 mounts to most small clamp-on and bolt-on outboards, provided the transom has adequate mounting clearance. The package includes one hydraulic PT-35 unit, one wire assembly with toggle switch, and one switch plate with rubber boot, making it a straightforward upgrade for boaters with basic tools.

Specifications

• Brand: T-H Marine
• Manufacturer Part Number: 52100
• Model Number: PT-35
• Power Rating: Up to 35 HP
• Set Back: 5-1/2 inches
• Trim and Tilt Range: 84 degrees
• Motor Mounting Inside Dimension: 11 inches
• Electric Hydraulic Actuator Rating: 7853 pounds of thrust
• Weight: 28 pounds
• Material: Aluminum
• Color: Silver
• Voltage: 12 Volts
• Operation Mode: Electric
• Mounting Type: Transom Mount
• Recommended Use: Freshwater and Saltwater
• UPC: 739697521009
• OEM Equivalent Part Number: T-H Marine PT35
• Warranty: 1 year limited warranty on actuator, 5 year limited warranty on frame

Fitment

Designed for outboard motors rated up to 35 HP, including clamp-on and bolt-on outboards used on jon boats, aluminum fishing boats, inflatable boats, tiller-steer outboards, and small skiffs and utility boats. Verify the transom provides adequate mounting clearance before installation.

Replaces (OEM)

• T-H Marine PT35

Frequently Asked Questions

What size outboard is the T-H Marine CMC PT-35 designed for? The PT-35 electric hydraulic tilt and trim, part number 52100, is designed for small outboards rated up to 35 HP, making it a match for jon boats, aluminum fishing boats, inflatables, and other lightweight rigs.

Does the PT-35 work with clamp-on outboards as well as bolt-on outboards? Yes, the T-H Marine CMC PT-35 is designed to work with most small clamp-on and bolt-on outboards as long as the transom provides enough flat mounting area for the unit.

Can I install the PT-35 tilt and trim myself? Many boaters with basic tools can install the PT-35 themselves since it is a fully self-contained electric hydraulic actuator with no external pumps or hydraulic lines to plumb, though it does require safely supporting the outboard and following the wiring instructions.

Is the CMC PT-35 suitable for saltwater use? Yes, the PT-35 (part 52100) is built with high-strength aluminum and corrosion-resistant components, making it suitable for both freshwater and saltwater environments; rinsing with fresh water after saltwater use is recommended to maximize service life.

What is included with the CMC PT-35 kit? Each PT-35 package includes one hydraulic PT-35 unit, one wire assembly with toggle switch, and one switch plate with rubber boot.

How much thrust does the PT-35 actuator provide? The electric hydraulic actuator in the CMC PT-35 is rated at 7853 lbs of thrust.

What is the trim and tilt range on the PT-35? The T-H Marine CMC PT-35 provides an 84 degree trim and tilt range.

How much does the PT-35 tilt and trim unit weigh? The CMC PT-35 (part 52100) weighs 28 pounds.

What material is the PT-35 made from? Aluminum is used for the PT-35 housing, giving it corrosion resistance for both freshwater and saltwater use.

What voltage does the CMC PT-35 run on? The PT-35 electric hydraulic actuator operates on 12 volts.

Is there an OEM equivalent part number for the CMC PT-35? Yes, part number 52100 is also listed under the equivalent designation T-H Marine PT35.

What is the warranty on the CMC PT-35? The PT-35 tilt and trim carries a 1 year limited warranty on the actuator and a 5 year limited warranty on the frame.