T-H Marine ELL-3/4 Barbed Elbow Fitting, 90 Degree, 3/4 Inch Hose ID

The T-H Marine ELL-3/4 is a 90 degree barbed elbow fitting molded specifically to fit marine hose dimensions for a 3/4 inch ID hose. Instead of bending hose sharply around a tight turn and risking a kink that restricts flow, this elbow lets the hose route through a clean 90 degree change in direction while keeping the barb securely seated. It is also commonly used as a hose junction fitting when repairing a damaged section of hose, letting you cut out the bad section and rejoin the two ends. Both legs of the fitting share the same barb dimension, so hose slides on and grips evenly on either side of the turn. This makes it a straightforward, reliable component for livewell plumbing, bilge and washdown hose runs, aerator lines, or any onboard plumbing where a 3/4 inch ID hose needs to change direction or be spliced without adding a rigid, kink-prone bend. Installation is simple: work the 3/4 inch hose ends over each barbed leg and secure with standard hose clamps.

Specifications

• Brand: T-H Marine
• Manufacturer Part Number: ELL-3/4
• Product Name: Barbed Elbow Fitting
• Fitting Angle: 90 degrees
• Hose Inside Diameter: 3/4 inch
• Barb Configuration: Equal barb dimension on both legs
• Use: Hose routing turn or hose junction/repair splice
• Weight: 1 pounds

Fitment

Fits any marine plumbing system using 3/4 inch ID hose.

Frequently Asked Questions

What hose size does the T-H Marine ELL-3/4 fit? The ELL-3/4 is sized for 3/4 inch ID (inside diameter) hose and is molded specifically to marine hose dimensions for a secure fit.

Can this elbow be used to repair a damaged hose? Yes, the ELL-3/4 barbed elbow can be used as a hose junction fitting to splice two ends of 3/4 inch ID hose together when repairing a damaged section.

Why use a 90 degree elbow instead of just bending the hose? Bending 3/4 inch ID hose sharply around a tight turn can kink it and restrict water flow; the ELL-3/4 elbow provides a molded 90 degree turn so the hose routes cleanly without kinking.

Is the barb size the same on both ends of the ELL-3/4? Yes, both legs of the T-H Marine ELL-3/4 elbow have the same barb dimension, so hose grips evenly regardless of which leg it is fitted to.

What is the ELL-3/4 made for, livewells or bilge lines? The ELL-3/4 barbed elbow works for any 3/4 inch ID hose run onboard, including livewell plumbing, aerator lines, bilge, and washdown hose systems.

How much does the ELL-3/4 weigh? The T-H Marine ELL-3/4 barbed elbow fitting weighs 1 pounds.

Do I need clamps to install this fitting? Standard hose clamps are used to secure the 3/4 inch ID hose ends onto each barbed leg of the ELL-3/4 elbow after the hose is worked onto the barb.

Does T-H Marine make this elbow in other hose sizes? T-H Marine's barbed elbow fitting line also includes sizes for 1/4 inch, 3/8 inch, 1-1/8 inch, and 1-1/2 inch ID hose; the ELL-3/4 is the 3/4 inch ID version.

What material is the ELL-3/4 elbow made from? The ELL-3/4 is a molded fitting built to marine hose dimensions; specific material composition is not specified.

Will the ELL-3/4 fit both push-on and threaded hose systems? The ELL-3/4 is a barbed fitting, designed for push-on 3/4 inch ID hose secured with a hose clamp, not a threaded connection.